Timeguard TGVL05 - Manual

Weathersafe Vision
Installation and Operating
Instructions
IP66 Products covered by
these instructions
TGVL01 One gang two way switch 10AX
TGVL02 Two gang two way switch 10AX
TGVL03 One gang bell push
TGVL05 One gang double pole switch 20A
TGV101 One gang socket switched 13A
TGV201 Two gang socket switched 13A
TGV104 One gang RCD spur
TGV204 Two gang RCD protected socket
13A (passive/latching)
TGV205 Two gang RCD protected socket
13A (active/non-latching)
TGV203 Combined timer and socket
TGV103 One gang switched fused spur 13A
General
Please note that all instructions are to be left with the
customer after installation.
The Weathersafe Vision range is manufactured from
tough, durable thermoplastic, and is intended for use in
an outdoor environment, or one in which the protection
provided by the Weathersafe Vision range is required.
All the products are rated IP66, for protection against
water and dust. All Weathersafe Vision products need to
be fi tted with waterproof cable and conduit entries to
maintain their IP rating once installed.
The weather plus range complies with the following
standards.
• IP66 rating: BS EN 60529
• Socket outlets: BS 1363
• RCD units: BS 7288
• Fused connection units: BS 1363
• Switches: BS EN 60669
• All products in the range comply with the low
voltage directive LV 72/23/EEC and where
relevant the EMC directive 89/336/EEC
Voltage: 230V AC 50Hz
Operating temperature range: -5° to 55°C
Installation instructions
• These products should be installed by a competent
person (e.g. qualifi ed electrician) in accordance with
these instructions and in compliance with the
appropriate clauses of the current edition if the IEE
wiring and building regulations. Sockets should be
connected via a suitable RCD device.
• Disconnect the mains electricity supply
before
installing.
• The Weathersafe Vision range is designed to be
mounted on a vertical fl at surface, with socket outlets
not more than 1 metre above the ground.
• The rear box shall be mounted on the wall using no.8
wood screws and wall plugs if necessary (see fi g. 1).
• If the mounting surface is uneven use a sheet of
marine ply as a base plate then fi t the rear box to it.
Fig. 1
Rear Box (double)
If conduit is to be used then please follow the
instructions below:
• The drain feature must be drilled out using
a 5mm drill if top or side entry conduit is used.
Opening this drain hole will reduce the IP rating
of the product. Remember – open out the lower
drain feature only and only if required by
conduit entry being used.
• If bottom entry conduit is used, there must be
adequate drainage from the lowest point of
the conduit.
• The relevant cable entry knockout should
be carefully removed by scoring the groove
around the knockout with a sharp knife and
then tapping it out with a small hammer.
A waterproof cable or conduit entry must
then be fi tted in its place.
• If two cable entry positions are used with
metal conduit, then earth continuity between
the conduits must be maintained.
• Ensure that the gasket is correctly fi tted,
and tighten the four screws (supplied) to fi x
the front cover in place (see fi g. 1). Do not
overtighten. Use of an electric screwdriver
is not recommended.
Operating Instructions
Fig. 2
Single and double boxes – side view of bottom.
• The lid may be opened by pressing in the tab(s)
on the front to release the snaps and then lifting
the lid (see fi g.2).
• Plugs may be inserted into the sockets and the
socket switches turned on.
• The lid should then be closed to maintain the
IP rating taking care to ensure that the cables
are aligned with the centre of the cable seals
(see fi g. 3). Finally engage the snaps (see fi g. 2)
by pulling out the tab(s) while maintaining
pressure to close the lid.
Fig. 3
Rear Box (double with 2 gang RCD sockets)
Cleaning
• Care should be taken when cleaning
this
product.
• Inside the lid should only be wiped with a
clean dry cloth.
• The outside can be cleaned with
mild
detergent.
• Solvent based cleaners should not be used.
• Advice should be sought before installing this
product in an environment where it is likely to
be subjected to chemicals, oils or solvents.
Weathersafe Vision Products with RCD’s
(TGV104, TGV204, TGV205)
Always test the RCD before use.
To test: Ensure supply is connected
RESET – press the grey (blue for TGV205) button
marked Reset (R), the status indicator should show red.
TEST – press the red button marked Test (T),
status indicator should show black. This indicates
that the RCD has been tripped and power has been
disconnected from the outlet.
RESET – press the grey (blue for TGV205) button
marked Reset (R) again, the status indicator
should show red.
If all the above operations work satisfactorily, the RCD
is safe for use.
If the procedure is not completed satisfactorily do not
use the RCD and seek professional advice.
In applications such as hand driers it may not be
practical to expect each user to test before use. In this
case we suggest an appropriate person applies the test
routine twice a day.
4 x fi xing holes for
no. 8 woodscrews
Drain feature,
use only lower if
required
Front cover
fi xing holes
Cable aligned with
centre of seals Status indicator
T
R
Push here and lift up
Snaps
Snaps
Fold Fold Fold
Fold Fold