Trimec ES150 Series Surface Mounted Electric Strike - Manual (Page 2)

Page 2 Page 3
Solenoid Leads Colour
Red
Blue
Supply Voltage
12 VDC
24 VDC
Current Draw
250 mA
187 mA
CAUTION! Incorrect supply voltage may cause damage not covered by warranty. Please check supply voltage with a suitable meter
to ensure it is within +/- 15% of the nominal voltage shown above with the strike powered.
This product has been designed for use in weather protected areas only. DO NOT OIL OR LUBRICATE.
Certifi cation
AS4145.2 compliant
BS5872 approved
CE compliant
up to 20-minutes fi re rating, depending on type of doorset
(in accordance with AS1905.1 - 1997, Part 1: Fire-resistant Doorsets)
Tested according to UL 1034:
1,500 lbs. (680 kg) static strength rating
70 foot-lbs. dynamic strength rating
1,000,000 cycles endurance rating
•
•
•
•
•
•
•
20
Mins
NOTE: As the 150 series strike will normally be used on an exit door, it is recommended that the strike should always be confi gured to
“Power to Lock” mode.
To change electric strike’s mode of lock operation, remove the 2 screws securing the lock to the body (see Fig. 4).
Depress the striker jaw and slide the strike out of the housing. If the electric strike locking mode is set to Power to Open, power up the
strike to enable rotation of the striker jaw before removal from housing.
Remove brass screw from strike body, invert strike and release the spring and 3 locking pins (2 x Short pin, 1 x Long pin).
Re-insert pins in in the manner shown for the desired mode of lock operation (Power to Open: see Fig. 5; Power to Lock: see Fig. 6),
followed by the spring.
Screw in the brass screw to strike body. This will secure the spring and locking pins.
Apply power to lock if necessary, depress striker jaw and insert body into housing. Secure the strike body in housing by screwing in the
2 screws.
1.
2.
3.
4.
5.
6.
Long Pin
Short Pins
Long Pin
Fig. 5 -
Power to Open (Fail-Secure) Confi guration
Fig. 6 -
Power to Lock (Fail-Safe) Confi guration
Small End of
Spring
Short Pins
Fig. 4 - Remove Screws, then Slide Strike Out of Housing
Depress Striker Jaw, Slide
Strike Out of Housing
Remove Screws from Body
150 SERIES SPARE PARTS & ACCESSORIES
The following are available as optional extras:
SPARE PARTS
Part Number Qty Per Pack Description
220100-501 1 12 V Solenoid Coil
220100-512 1 12 V Weather Resistant Solenoid Coil
220100-502 1 24 V Weather Coil
220100-511 1 24 V Weather Resistant Solenoid Coil
220100-509 1 48 V Solenoid Coil
200100-100 5 100 Series Locking Pins, Spring and Stop Screw
200100-110 5 100 Series Weather Resistant Locking Pins, Spring and Stop Screw
DA0024, Issue 5: 25th July 2007
5 Year Limited Warranty
ASSA ABLOY Australia guarantees for a period of 5 years in accordance with Trimec’s Standard Warranty Conditions, against defects in
manufacture, workmanship or materials, provided that all electrical and mechanical installation requirements are adhered to as per this
datasheet. All third party and consequential claims are expressly excluded from this warranty.
warranty
ASSA ABLOY Australia
2/16 Atkinson Road
Taren Point 2229
NSW, Australia
www.assaabloyasiapacifi c.com
CHANGING MODE OF LOCK OPERATION ELECTRICAL SPECIFICATIONS