Ultravation Photronic Air Purification HEPA Bypass - DC-IH-0202 - Manual (Page 2)

2
Shipping and Packaging List:
• Filter Housing including Access Door
• Merv 11 Media Air Filter
• HEPA
Filter
• 1- Door Handle w/ hardware
• PCO
Filter
• Electrical
Enclosure
• 2- 12” T3 UVC Lamps
• *2- UVC Lamps Part:
12” T3 UVC lamp option
OR
17” T3 UVC lamp option
• *4- 1 inch UVC lamp mounting screws
• *8- 1/2 inch 5/16 self tapping screws
• *2- UVC Lamp Mounting Plates
* Included when Remote UVC option is purchased
Introduction and Applications:
This Ultravation Photronic HEPA Media Air Cleaner is a
complete whole house air cleaning system. This high
efficiency air filtration unit is designed to remove dirt,
dust, pollen, and microscopic particles: reduce
unpleasant odors, VOC gases and the microbial
population from the air that circulates through it. By
adding this device to your HVAC system, you are
helping to create a cleaner indoor living environment for
your whole household.
The system works in 2-3 steps (depending on model
purchased, some models do not include the germicidal
protection in step 3)
STEP 1: Trapping particles in the pleats of the MERV 11
media filter. With an extra large surface area, the filter
allows for maximum dirt holding capacity and a long,
useful filter life with minimum air flow restriction.
STEP 2: VOC’s and gases such as the fumes from new
carpets, paints, nail polish, cigar and cigarette smoke
are drastically reduced photo chemically via a patented
process known as photo catalytic conversion or photo
catalytic oxidation.
(Option)STEP 3: Germicidal UVC light is applied to the
Air to drastically reduce or eliminate unwanted virus,
bacteria and mold.
This air cleaner is to be installed in a forced air heating,
cooling and ventilation system. It should be installed so
that all the system’s air is circulated through the filter first
and VOC Section second. The air cleaner will only filter
the air that is circulated through it. For maximum filtration
effect, set your blower to operate continuously. (Lower
speeds allow for higher efficiency)
Safety Precautions:
It is recommended that this unit be installed and
maintained by a trained technician:
WARNING: UV Hazard. Always protect eyes from
ultraviolet light. NEVER look at UV lamps in
operation. Unplug or disconnect power before re-
lamping or servicing.
WARNING: Severe eye damage or temporary
blinding may occur.
WARNING: DO NOT operate UVC lamps outside of
Air Handler. Mount lamp base to duct first.
WARNING: No openings in duct are allowed which
would give direct line-of-sight to the UV light.
In the event of accidental breakage or replacement of
the ultraviolet lamp, please ensure that the lamp is
disposed of in accordance with local and state
environmental laws regarding fluorescent lamps
containing mercury.
Notice:
All wiring inside of the duct or air handling system in
direct line of site of the UV lamp must be shielded with
aluminum foil tape or equivalent non-combustible
material. When installing this unit, select a mounting
location that prevents ultraviolet light exposure to
plastic flexible duct liner or other plastic components
with unknown resistance to ultraviolet light. Ultraviolet
light may cause color shift or structural degradation of
plastic HVAC components
Power Consumption UV-A, UV-C lamps
Lamp Type Quantity Required
12-inch UVC lamp is 12 watts each 2
12-inch UVC lamp is 12 watts each 2
17-inch UVC lamp is 22 watts each 2
Installation requirements:
This unit is designed to be powered up constantly
and should not cycle on and off with a blower
motor.
Unit must be installed either within 6 feet of a 120
power outlet, or hardwired per local and state electrical
code.
There must be minimum 26 inches in front of the door
for filter and lamp replacement.
Note: Handle fits either door. A Phillips screw driver
will be required to install the handle. Handle holes are
behind the label on either door, depending on the
orientation of the installation.