Brother HL-8050N - Manual (Page 8)

7
Federal Communications Commission (FCC) Declaration of
Conformity (For U.S.A. Only)
Responsible Party: Brother International Corporation
100 Somerset Corporate Boulevard
Bridgewater, NJ 08807-0911
USA
Telephone: (908) 704-1700
declares, that the products
Product name: Laser Printer
Model number: HL-8050N
Product options: All
complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Adjust or relocate the receiving antenna.
– Increase the distance between the equipment and receiver.
– Connect the equipment to an AC power outlet/socket on a circuit
different from that which the receiver is already connected.
– Call the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used in order to ensure compliance with
the limits for a Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd.
could void the user’s authority to operate the equipment.
Industry Canada Compliance Statement (For Canada Only)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Laser Safety (100 to 127 Volt Model Only)
This printer is certified as a Class I laser product under the U.S. Department
of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. This
means that the printer does not produce hazardous laser radiation.
Since radiation emitted inside the printer is completely confined within
protective housings and external covers, the laser beam cannot escape from
the machine during any phase of user operation.
FDA Regulations (100 to 127 Volt Model Only)
U.S. Food and Drug Administration (FDA) has implemented regulations for
laser products manufactured on and after August 2, 1976. Compliance is
mandatory for products marketed in the United States. The label shown on
the back of the printer indicates compliance with the FDA regulations and
must be attached to laser products marketed in the United States.
☛ Caution: Use of controls, adjustments or the performance of
procedures other than those specified in this manual may
result in hazardous radiation exposure.
IEC 60825 specification (220 to 240 Volt Model Only)
This printer is a Class 1 laser product as defined in IEC 60825 specifications.
The label shown below is attached in countries where required.
This printer has a Class 3B laser Diode that emits invisible laser radiation in
the Scanner Unit. The Scanner Unit should not be opened under any
circumstances.
☛ Caution: Use of controls, adjustments or performance of
procedures other than those specified in this manual may
result in hazardous radiation exposure.
Regulations
EC Declaration of Conformity under the R & TTE Directive
Manufacture
Brother Industries Ltd.,
15-1, Naeshiro-cho, Mizuho-ku,
Nagoya 467-8561, Japan
Herewith declare that:
Products description: Laser Printer
Product Name: HL-8050N
is in conformity with provisions of the R & TTE Directive (1995/5/EEC
2002) and we declare compliance with the following standards:
R&TTE: EN300330-2 V1.1.1
EN301489-3 V1.3.1
CE0682
Safety: EN60950: 2000
EMC: EN55022: 1998 + A1: 2000 Class B
EN55024: 1998
EN61000-3-2: 1995 + A14: 2000
EN61000-3-3: 1995
Year in which CE marking was First affixed: 2003
Issued by: Brother Industries, Ltd.
Date: 7 July, 2003
Place: Nagoya, Japan
Signature:
Takashi Maeda
Manager
Quality Management Group
Quality Management Dept.
Information & Document Company
MANUFACTURED:
Brother Industries, Ltd.,
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21
CFR subchapter J.
CLASS 1LASERP RODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
!