Dishwasher, Front, Left – Electrolux EI24ID30QB User Manual
Page 3: Right, Electrolux major appliances, n.a
High standards of quality at Electrolux Home Products, Inc.
mean we are constantly working to improve our products.
We reserve the right to change specifications or
discontinue models without notice.
FPO
Meets
requirements of
ASSE 1006
Dishwasher
EI24ID80Q / EI24ID50Q / EI24ID30Q
Front
33
3
/
4
"
Adjustable
to 35
3
/
4
"
*
23
3
/
4
"
*Height only adjustable to 35
3
/
4
" max. when installed in 35
3
/
4
" max.
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
Left
24
1
/
4
"
Power supply & water inlet location
(bottom rear)
50
1
/
4
"
Right
Door in 90°
open position
27
3
/
4
"
22
1
/
2
"
3
1
/
2
" min. to
4
1
/
2
" max.
1"
2
1
/
4
"
2
1
/
4
"
**
NOTE:
35
3
/
4
" max.
height for standard
cabinetry cutout.
(
5
/
16
" min. clearance
required from unit to
underside of countertop.)
3"
18"
24"
min.
Electrical, water,
and drain lines
must be confined
to shaded area
1
1
/
4
"
24"
3"
90°
90°
Preferred
drain areas
3"
34"
min. to
35
3
/
4
"
max.
**
Built-In Dishwasher Specifications
•
Product Weight – 98 Lbs.
•
Voltage Rating – 120V/60Hz/15 Amps
•
Connected Load (kW Rating) @120 Volts = 1.44 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120V = 15A
•
Always consult local and national electric & plumbing codes.
Meets requirements of ASSE 1006 — integral air gap on supply.
•
Water Pressure – Hot water line to dishwasher must provide between 20 and
90 pounds per square inch (psi) with at least 120° F hot water temperature.
•
Make sure location has correct drain, water and electrical outlets to make
connections.
•
Electrical and water supplies should enter cabinet opening on floor, or
through back or side walls, as shown in shaded areas.
•
Keep back free of drain, water & electrical supply.
•
Connections preferably located toward left side of dishwasher. Do not cross
drain, water or electrical lines in front of motor, blower or frame.
•
If connecting drain hose to sink trap, local code may require installation of
Air Gap Kit (not included).
•
Leveling legs supplied to adjust height. (Note: Height only adjustable to
35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout.
5/16" min. clearance required from top of unit to underside of countertop.
Dimensions do NOT include insulation — insulation blanket may be
compressed during installation.)
•
When installing adjacent to wall, cabinet or other obstruction that extends
beyond front edge of unit, allow 2" minimum clearance between opened door
and obstruction.
•
Floor should be flat and free of obstructions.
•
When installing at end of cabinet line, sides and back must be fully enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher, including
underside of countertop, with oil-based paint or moisture-proof polyurethane
to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
DISHWASHER
EI24ID30Q S / W / B
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxappliances.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxappliances.ca
EI24ID30Q 04/14
© 2014 Electrolux Home Products, Inc.