American Audio DV2 USB - Manual (Page 9)

25. LIne LeVeL SeLeCtOr SWItCh - This switch is used to change the mode of PHONO INPuT
jAckS (26 and 28). When connecting turntable to these jacks be sure the switch is in the PHONO
position, and when using line level input devices be sure this switch is in the AUX position. Always be
sure main power is shut off before change the position of the Line Level Selector Switch.
26. ChanneL 1: PhOnO 1 InPUt/aUX 1 jaCkS - The type of input must directly reflect the selected
mode of the LINE LEVEL SELEcTOR SwITcH (25). Connect turntables equipped with MM pickup car-
tridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments may be connected to these jacks as long as the LINE LEVEL SELEcTOR
SwITcH (25) is in the “AUX 1” position. The red colored RCA jack represents the right channel input
and the white represents the left channel input.
These RCA jacks are also routed to the USB interface inputs. Allowing you to record phono or
line level signals via the Aux level inputs. This can also be used with drivers that support
multiple channel USB audio streams on DJ software.
27. ChanneL 1: LIne 1 rCa InPUt jaCkS - These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input.
28. ChanneL 2: PhOnO 2 InPUt/aUX 2 jaCkS - The type of input must directly reflect the selected
mode of the LINE LEVEL SELEcTOR SwITcH (25). Connect turntables equipped with MM pickup car-
tridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments may be connected to these jacks as long as the LINE LEVEL SELEcTOR
SwITcH (25) is in the “AUX 2” position. The red colored RCA jack represents the right channel input
and the white represents the left channel input.
29. ChanneL 2: LIne 2 rCa InPUt jaCkS - These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input.
These RCA jacks are also routed to the USB interface inputs. Allowing you to record phono or
line level signals via the Aux level inputs. This can also be used with drivers that support
multiple channel USB audio streams on DJ software.
30. reC OUt - This is a low current unbalanced output source designed for various tape and CD
recorders. The Record Out (REC OUT) level is dictated by the cHANNEL FADER LEVEL (8), it is not
influenced by the MASTER VOLuME cONTROL (1).
31. rCa MaSter OUtPUtS - The RCA master output unbalanced jacks send a low current unbal-
anced output signal.
32. BaLanCeD XLr MaSter OUtPUtS - The Master Output includes a pair XLR Balanced
JACKS as well as a pair RcA uNbALANcED jAckS (31). The 3-pin XLR jacks send a high current
balanced output signal. These jacks should be used when you will be driving an amp or other audio
equipment with a balanced input, or whenever you will be running a signal line greater than 15 feet.
Always, use these jacks whenever possible.
DV2 USB Controls and Features Cont.
© American Audio ® - www.AmericanAudio.us - DV2 USB Instruction Manual Page 9