Installation instructions, Warning, Exhaust information – GE GFDN120EDWW User Manual

Page 4: Exhaust system check list, Exhaust length for long vent models, Exhaust length for normal vent models

Advertising
background image

4

Installation Instructions

3

EXHAUST INFORMATION

WARNING -

IN CANADA AND IN THE

UNITED STATES, THE REQUIRED EXHAUST DUCT

DIAMETER IS 4 in (102mm). DO NOT USE DUCT

LONGER THAN SPECIFIED IN THE EXHAUST LENGTH
TABLE.

8VLQJH[KDXVWORQJHUWKDQVSHFL¿HGOHQJWKZLOO
• Increase the drying times and the energy cost.
• Reduce the dryer life.
‡$FFXPXODWHOLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG

The correct exhaust installation is YOUR RESPONSIBILITY.
Problems due to incorrect installation are not covered by the
warranty.
Remove and discard existing plastic or metal foil transition duct
and replace with UL listed transition duct.
The MAXIMUM ALLOWABLE duct length and number of bends
of the exhaust system depends upon the type of duct, number
RIWXUQVWKHW\SHRIH[KDXVWKRRG ZDOOFDS DQGDOOFRQGLWLRQV

noted below. The maximum duct length for rigid metal duct is
shown in the table below.

• )RUHYHU\H[WUDƒHOERZUHGXFHWKHDOORZDEOHYHQWV\VWHPOHQJWKE\IW

• 7ZRƒHOERZVZLOOEHWUHDWHGOLNHRQHƒHOERZ

• )RUWKHVLGHH[KDXVWLQVWDOODWLRQVDGGRQHƒHOERZWRWKHFKDUW

• 7KHWRWDOYHQWV\VWHPOHQJWKLQFOXGHVDOOWKHVWUDLJKWSRUWLRQVDQGHOERZVRIWKHV\VWHP WUDQVLWLRQGXFWLQFOXGHG 

EXHAUST SYSTEM CHECK LIST

HOOD OR WALL CAP
• Terminate in a manner to prevent back drafts or entry of birds or other wildlife.
‡ 7HUPLQDWLRQVKRXOGSUHVHQWPLQLPDOUHVLVWDQFHWRWKHH[KDXVWDLUÀRZDQGVKRXOGUHTXLUHOLWWOHRUQRPDLQWHQDQFHWRSUHYHQW

clogging.

• Never install a screen in or over the exhaust duct. This could cause lint build up.
• :DOOFDSVPXVWEHLQVWDOOHGDWOHDVWLQDERYHJURXQGOHYHORUDQ\RWKHUREVWUXFWLRQZLWKWKHRSHQLQJSRLQWHGGRZQ

4" DIA.

4"

4" DIA.

4" DIA.

2-1/2"

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

No. of 90°

Elbows

Rigid

Metal

Rigid

Metal

150 Feet

135 Feet

125 Feet

115 Feet

105 Feet

125 Feet

115 Feet

105 Feet

95 Feet

85 Feet

0

1

2

3

4

Use only for short

run installations

5

95 Feet

75 Feet

EXHAUST LENGTH

FOR LONG VENT MODELS

4" DIA.

4"

4" DIA.

4" DIA.

2-1/2"

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

No. of 90°

Elbows

Rigid

Metal

Rigid

Metal

90 Feet
60 Feet
45 Feet
35 Feet
25 Feet

60 Feet
45 Feet
35 Feet
25 Feet
15 Feet

0
1
2
3
4

Use only for short

run installations

EXHAUST LENGTH

FOR NORMAL VENT MODELS

Advertising