Asus Vintage-AH1 - Manual (Page 56)

4 - 7 4 - 7 4 - 7 4 - 7 4 - 7 A S U S V i n t a g e - A H 1 A S U S V i n t a g e - A H 1 A S U S V i n t a g e - A H 1 A S U S V i n t a g e - A H 1 A S U S V i n t a g e - A H 1
4 . 4 . 4 . 4 . 4 . C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s C P U a n d C h a s s i s F a n c o n n e c t o r s
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N ) ( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N ) ( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N ) ( 3 - p i n C P U _ F A N , 3 - p i n C H A _ F A N )
The fan connectors support cooling fans of 350 mA~740 mA (8.88 W
max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the
fan cables to the fan connectors on the motherboard, making sure that
the black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 before using Serial ATA hard disk drives.
• When using the connectors in standard IDE mode, connect the primary
(boot) hard disk drive to the SATA1 or SATA2 connector.
®
SATA connectors
SATA3
GND
RSA
T A_TXP3
RSA
T A_TXN3
GND
RSA
T A_RXP3
RSA
T A_RXN3
GND
SATA4
GND
RSA
T A_TXP4
RSA
T A_TXN4
GND
RSA
T A_RXP4
RSA
T A_RXN4
GND
SATA1 SATA2
GND RSA
T A_TXP1
RSA
T A_TXN1
GND RSA
T A_RXP1
RSA
T A_RXN1
GND GND RSA
T A_TXP2
RSA
T A_TXN2
GND RSA
T A_RXP2
RSA
T A_RXN2
GND
®
Fan connectors
CPU_FAN
CHA_FAN
GND
Rotation
+12V
GND
Rotation
+12V