STEINEL HG 350 ESD - Manual (Page 2)

- 2 -
for choosing a STEINEL heat gun. This tool can be used for completing a wide range of jobs safely and reliably, such as
soldering, de-soldering, shrink-fitting, etc.
All STEINEL tools are manufactured to the highest standards and undergo a strict process of quality control. Used properly
(please refer to the safety precautions provided below), the tool will give you prolonged service and lasting satisfaction.
Thank you
IMPORTANT SAFETY INSTRUCTIONS
READ THESE INSTRUCTIONS
UL WARNING: Read this instruction book before using. To reduce risk of fire or electric
shock, do not expose to rain or moisture. Store indoors. Connect to grounded outlet only. When
using electric tools, basic safety precautions should always be followed to reduce risk of fire, elec-
tric shock and personal injury. This heat gun operates up to 930°F with no visual indication of tem-
perature (no flame). Never leave device unattended. Otherwise risk of fire. The heat stream at the
outlet nozzle will burn flesh. Do not turn on heat gun with hand in front of nozzle. DO NOT USE
NEAR COMBUSTIBLE LIQUIDS. DO NOT USE FOR: ● Heating gas engines ● Heating car batteries
● Thawing refrigerator equipment.
WARNING!
This tool is capable of producing temperatures up to 930°F of flameless heat at the nozzle. ALWAYS:
● Direct the heat away from yourself and others.
● Prevent ignition of combustible materials on or near the workpiece.
● Prevent blockage of intake and nozzle openings.
● Keep a fully charged fire extinguisher on hand.
● Allow the nozzle and accessory tips to cool to room temperature before storage.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known (to the State of California) to cause cancer, birth defects, or other
reproductive harm. Some examples of these chemicals are:
● lead from lead-based paints,
● crystalline silica from bricks and cement and other masonry products, and
● arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Cautions
1. WARNING: Hidden areas such as behind walls, ceilings, floors, soffit boards and other panels may contain
flammable materials that could be ignited by the heat gun when working in these locations. The ignition of
these materials may not be readily apparent and could result in property damage and injury to persons. Do
not use if in doubt about this hazard. When working in these locations, keep the heat gun moving in a back-
and-forth motion. Lingering or pausing in one spot could ignite the panel or the material behind it.
2. This heat gun can produce up to 930°F of flameless heat at the nozzle. Do not direct airstream at clothing,
hair or other body parts. Do not use as a hair dryer.
3. Do not use near flammable liquids or in an explosive environment (fumes, gases or dust). Remove materials
or debris, that may become ignited, from work area.
4. Always hold tool by plastic enclosure. The metal nozzle requires approximately 20 minutes to cool after tur-
ning off the tool. Do not touch nozzle or accessory tips until cool.
5. Do not store tool until nozzle has cooled to room temperature. Place tool in a clear area away from combus-
tible materials while cooling.
6. Do not cut off airflow by placing nozzle too close to workpiece. Keep intake vents clean and clear of obst-
ructions.
7. Place cord in a position that won’t cause tipping.
8. Do not leave tool unattended while running or cooling down. Otherwise risk of fire.
9. Keep a fully charged fire extinguisher nearby.
10. Do not direct airflow directly on glass.
English
- 3 -
11. Shield materials around the heated area to prevent damage or fire.
12. Use only with 120 V AC voltage.
13. Do not use in wet conditions.
14. Not to be used by children. This is not a toy and should be respected.
15. Do not use in bath or over water.
16. Safety glasses should be worn when using this tool.
17. It is recommended that leather gloves be worn when using a heat gun.
18. Always unplug after use.
19. WARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint
may contain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes
prior to 1950 is likely to contain lead. Once deposited on surfaces, hand to mouth contact can result in
the ingestion of lead. Exposure to even low levels of lead can cause irreversible brain and nervous system
damage; young and unborn children are particularly vulnerable. Before beginning any paint removal process
you should determine whether the paint you are removing contains lead. This can be done by your local
health department or by a professional who uses a paint analyzer to check the lead contact of the paint to
be removed. LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL AND SHOULD
NOT BE REMOVED USING A HEAT GUN.
20. Do not allow dust, debris or other contamination to enter the heat gun air intake. They may ignite or cause
damage to the tool.
21. Do not place hot tool in holster or other device which retains or directs heat around tool body.
Persons removing paint should follow these guidelines.
1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated. Open the win-
dows and put an exhaust fan in one of them. Be sure the fan is moving the air from inside to outside.
2. Remove or cover any carpets, rugs, furniture, clothing, cooking utensils and air ducts.
3. Place drop cloths in the work area to catch any residue. Wear protective clothing such as extra work
shirts, overalls and hats.
4. Work in one room at a time. Furnishings should be removed or placed in the center of the room and
covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop
cloths.
5. Children, pregnant or potentially pregnant women and nursing mothers should not be present in the work
area until the work is done and all clean up is complete.
6. Wear a dust respirator mask or a dual filter (dust and fume) respirator mask which has been approved
by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health
(NIOSH), or the United States Bureau of Mines. These masks and replaceable filters are readily available
at major hardware stores. Be sure the mask fits. Beards and facial hair may keep masks from sealing pro-
perly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.
7. Use caution when operating the heat gun. Keep the heat gun moving as excessive heat will generate fu-
mes which can be inhaled by the operator.
8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth before eating
or drinking. Do not smoke or chew gum or tobacco in the work area.
9. Clean up all removed residue and dust by wet mopping the floors. Use a wet cloth to clean all walls,
sills and any other surface where residue or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM.
Use a high phosphate detergent or trisodium phosphate (TSP) to wash and mop areas.
10. At the end of each work session put the residue and debris in a double plastic bag, close it with tape
or twist ties, and dispose of properly.
11. Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of the
dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work
clothes. Wash hair and body thoroughly with soap and water.
SAVE THESE INSTRUCTIONS
English
HG350ESD_Kabelvs_3spr_USA.indd 3-4 15.03.10 10:33