American Standard CORNER DUET W/SEAT 2351 - Manual (Page 4)

4 754407-100 Rev. B
CORNER DUET WITH SEAT
CENTURION ' X "
CONTEMPO OVAL
FREE SPIRIT ' X 54"
51
71

4
EZHEAT-100
EZHEAT-100
EZHEAT-100
EZHEAT-100
N/A
N/A
N/A
N/A
751755-100
751755-100
N/A
751755-100
OPTIONAL COMPONENTS (NOT INCLUDED)
E-Z INSTALL HEATER APRON KIT TILE BEAD KIT
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard Woodworking Tools
• Personal Safety Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 4 Stringers
• Drop Cloth
• Cement, Plaster, Grout
General Installation Information
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After
inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard,
tile, etc., the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage or
mishandling! Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the
safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are
provided by others.
For electrical requirements, refer to section titled “Whirlpool Electrical Installation Instructions”.
Check for availability of optional American Standard wall tiling bead (required for recess installation).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
DESCRIPTION MODEL #
LIST OF OPTIONAL COMPONENTS (NOT INCLUDED):
• For these components please see your Vendor.
! WARNING: Do not lift whirlpool by the piping harness at any time.
SPECIFICATIONS:
TABLE 1: GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS
SIDE VIEW DRAIN / OVERFLOW END VIEW
L
H
W
C
A
B
J
51
Corner
71
' x "

Oval
4
' x 54"
A 1-/"
(40 mm)
B 4"
(10 mm)
A 15-1/"
(4 mm)
B 10"
(54 mm)
A 1-1/"
(470 mm)
B 15-/4"
(400 mm)
A 17"
(4 mm)
B "
(14 mm)
1-5/"
(1mm)
"
(15mm)
-1/4"
(10mm)
N/A
C 1"
(4 mm)
C 0-1/4"
(514 mm)
C "
(54 mm)
C 1-/4"
(55 mm)
See Pier
Cutout
Dimensions
70-1/"
(171 mm)
x 4-1/"
(7 mm)
See Pier
Cutout
Dimensions
70-1/"
(171 mm)
x 5"
(14 mm)
N/A
7-/1"
(1 mm)
x 4-1/"
(7 mm)
N/A
7-/1"
(1 mm)
x 5-1/"
(14 mm)
L 4-1/" (14mm)
W 0-1/" (157mm)
H 0-1/" (51mm)
L 7" (1mm)
W " (14mm)
H 1-/4" (55mm)
L 7" (1mm)
W 4" (107mm)
H 5-1/" (4mm)
L 7" (1mm)
W 54" (17mm)
H -1/4" (51mm)
Description Drain / Overflow Cut Out Pier
G x F
Rough-In Recess
E x D
Tub Edge to
Centerline Overflow:
J
Height to
Underside of Deck:
C
Dimensions
L-W-H