CMP C2K - Manual

INSTALLATION INSTRUCTIONS FOR
INSTALLATION OF CMP CABLE
GLAND TYPE C2K
FOR TERMINATION OF CABLES WITH WIRE BRAID, TAPE ARMOUR (STA/DSTA), STRIP ARMOUR AND
SINGLE WIRE ARMOUR (SWA). FOR USE IN HAZARDOUS AREAS
INCORPORATING EC DECLARATION OF CONFORMITY TO DIRECTIVE 94/9/EC
CM
P
Do
cu
m
en
tN
o.
FI
44
0
Is
su
e
2
01
/1
3
0518
Notified Body: Sira Certification Service, Rake Lane, Chester CH4 9JN, England.
I, the undersigned, hereby declare that the equipment referred to herein conforms to the requirements of the ATEX Directive 94/9/EC and the
following standards:-
EN60079-0:2006, EN60079-1:2007, EN60079-7:2007, BS 6121:1989, EN50262:1998 (Amd 2001), EN61241-0:2004, EN61241-1:2004
Dr Geof Mood - Technical Director - (Authorised Person)
DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH
www.cmp-products.com
Logo’s shown for illustration purposes only. Please check certification for details
CABLE GLAND CABLE GLAND
TYPE C2K TYPE C2K
Cable
Connector
Size
Available Entry Threads
Thread Length
Cable
Bedding
Diameter
Overall Cable
Diameter
Armour Wire Diameter
Across
Flats
Across
Flats
Protrusion
Length
Ordering Reference
(NP Brass NPT)
PVC
Shroud
Reference
*
Connector
Weight
(Ozs)
Standard Option
Grooved Cone Stepped Cone
Metric NPT NPT Actual NPT Min Metric Max Min Max Min Max Min Max Min Max Max Max
20S/16 1/2" 3/4" M20 0.630 0.591 0.461 0.240 0.453 0.006 0.020 0.035 0.049 0.945 1.021 2.303 20S16C2K1RA531 PVC06 4.65
20S 1/2" 3/4" M20 0.630 0.591 0.461 0.374 0.626 0.006 0.020 0.035 0.049 0.945 1.021 2.303 20SC2K1RA531 PVC06 4.65
20 1/2" 3/4" M20 0.630 0.591 0.551 0.492 0.823 0.008 0.020 0.035 0.049 1.201 1.112 2.382 20C2K1RA531 PVC06 6.84
25S 3/4" 1 M25 0.669 0.591 0.787 0.551 0.866 0.008 0.024 0.049 0.063 1.476 1.594 2.657 25SC2K1RA532 PVC09 10.78
25 3/4" 1" M25 0.669 0.591 0.787 0.717 1.031 0.008 0.024 0.049 0.063 1.476 1.594 2.657 25C2K1RA531 PVC09 10.78
32 1" 1 1/4" M32 0.787 0.591 1.035 0.933 1.335 0.008 0.024 0.063 0.078 1.811 2.008 2.736 32C2K1RA532 PVC11 16.49
40 1 1/4" 1 1/2" M40 0.787 0.591 1.268 1.098 1.591 0.008 0.031 0.063 0.078 2.165 1.956 3.071 40C2K1RA534 PVC15 23.89
50S 1 1/2" 2" M50 0.787 0.591 1.504 1.386 1.839 0.008 0.031 0.078 0.098 2.362 2.338 2.972 50SC2K1RA535 PVC18 26.43
50 2" 2 1/2" M50 0.906 0.591 1.736 1.591 2.091 0.012 0.031 0.079 0.098 2.756 2.827 3.169 50C2K1RA536 PVC21 36.79
63S 2" 2 1/2" M63 0.906 0.591 1.969 1.795 2.339 0.012 0.031 0.079 0.098 2.953 3.189 3.602 63SC2K1RA536 PVC23 37.85
63 2 1/2" 3" M63 0.984 0.591 2.205 2.150 2.594 0.012 0.031 0.079 0.098 3.150 3.402 3.622 63C2K1RA537 PVC25 45.11
75S 2 1/2" 3" M75 0.984 0.591 2.441 2.323 2.839 0.012 0.031 0.098 0.118 3.504 3.784 3.898 75SC2K1RA537 PVC28 65.55
75 3" 3 1/2" M75 1.417 0.591 2.677 2.262 3.091 0.012 0.031 0.098 0.118 3.898 4.209 4.016 75C2K1RA538 PVC30 89.87
90 3 1/2" 4" M90 1.417 0.591 3.150 3.000 3.559 0.012 0.031 0.124 0.157 4.488 4.847 4.724 90C2K1RA539 PVC32 128.63
Dimensions are displayed in inches unless otherwise stated
Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS
Tel: +44 191 265 7411 • Fax: +44 191 265 0581
E-Mail: [email protected] • Web: www.cmp-products.com
TECHNICAL DATA
CABLE GLAND TYPE : C2K
INGRESS PROTECTION : IP66, IP67, IP68
PROCESS CONTROL SYSTEM : BS EN ISO 9001
: ISO/IEC 80079-34:2011
HAZARDOUS AREA CLASSIFICATION
ATEX CERTIFICATION No : SIRA 06ATEX1097X
ATEX CERTIFICATION CODE : II 2 GD Ex e II / Ex tD A21 IP66
IEC Ex CERTIFICATION No : IEC Ex SIR.06.0042X
IEC Ex CERTIFICATION CODE : Ex e II / Ex tD A21 IP66
INSTALLATION INSTRUCTIONS
Installation should only be performed by a competent person using the correct tools. Spanners should be used for tightening. Read all instructions
before beginning installation.
SPECIAL CONDITIONS FOR SAFE USE
1. The cable gland ranges shall only be used where temperatures at the point of entry is between -60°C and +130°C.
2. C2K cable glands are only suitable for fixed installations. Cables must be effectivelu clamped to prevent twisting and pulling
3. The entry component threads may need additional sealing to maintain the ingress protection rating as applicable to the associated equipment to
which it is attached
ACCESSORIES
The following accessories are available from CMP Products, as optional extras, to assist with fixing, sealing and earthing :-
Locknut | Earth Tag | Serrated Washer | Entry Thread (I.P.) Sealing Washer | Shroud *