JELD-WEN JII019 Impact Handle and Lock Set - Manual

INSTALLATION INSTRUCTIONS
for Impact Handle and Lock Set (JII019)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s
recommended installation instructions for the impact handle and lock
set. Read these instructions thoroughly before beginning.
These instructions supplement the assembly and installation
instructions for the patio door. Please use both the attached
instructions and this supplement to properly install the patio door.
Note to Installer: Provide a copy of these instructions to the building
owner. By installing this product, you acknowledge the terms and
conditions of the limited warranty as part of the terms of the sale.
SAfeTy
Wear protective gear (e.g. safety glasses, gloves, ear protection, etc.). •
Operate hand/power tools safely and follow manufacturer’s operating •
instructions.
Use caution when working at elevated heights.
•
If INJURy OCCURS, IMMeDIATeLy SeeK MeDICAL ATTeNTION!
ImPORTANT INfORmATION
INSTALL HANDLE & LOck SET
INCLUDeD PARTS
A Interior/exterior
handles
B Lock body
c face plate
D cylinder locks
E Lock keeper
Items not shown:
- Assembly screws
- keys
NeeDeD TOOLS
- Small flat head
screwdriver
- Phillips screwdriver
- Drill with bits and
drivers
INCLUDeD PARTS & NeeDeD TOOLS
B
E
A
D c
INSTALL hANDLeS & CyLINDeR LOCKS
1. Install the handles
using the two 2 1/4"
machine screws. Install
the handle with screw
holes on the interior.
2. If the lock body has
not been installed
into the jamb of the
operating panel, align
the cylinder lock holes
with the holes in the
panel and secure with
two 3/4" screws. Do
not fully tighten the
lock body screws.
3. Back out the two
cylinder lock security
screws until they do
not block the cylinder
lock holes.
4. Slip a lock washer
onto each cylinder
lock.
5. Position the keyed
cylinder lock unit on
the exterior side of
the door panel, and
the turn latch on the
interior.
6. Simultaneously screw the cylinder lock units in opposite directions
into the holes on both the interior and exterior of the door panel
until they are snug with the door panel. Both must be positioned at
6 o’clock so that the security screws will engage the groove in the
cylinder locks.
7. Use a small flat head screwdriver to tighten the security screws until
they are flush with the face of the lock body.
Note! If the security screws are tight but not flush, the cylinder lock
units will need to be rotated slightly clockwise or counterclockwise.
8. Test the lock to make sure it functions properly.
9. Tighten the lock body screws.
INSTALL fACe PLATe & KeePeR
1. Install the face plate
using a 3/4" screw at
the top and bottom
and a 1/4" screw in
the middle.
2. Extend the lock hook
and hang the keeper
on the hook with the
metal spring flap up
and facing the jamb.
3. close the door and
mark the jamb at the
top and bottom of the
keeper.
4. Position the keeper
between the marks
and drive a #10 x 3"
screw in the center
of each elongated
adjustment hole.
5. close the door and
test the lock to make
sure it engages the
keeper properly.
Adjust up or down as
necessary.
6. Drive screws into the
remaining two holes
and tighten all screws.
Lock body
Interior
handle
Exterior
cylinder
lock
Security
screw
groove
Lock
washer
Interior
cylinder
lock
face
plate
Lock
keeper
Adjustment
hole
(08/08)
© 2008 JELD-WEN, inc. | JELD-WEN and Reliability for real life are registered trademarks of JELD-WEN, inc., Oregon USA.
All other trademarks are the property of their respective owners.
Security
screws