JELD-WEN JCM004 Interior and Exterior Door Slabs and Systems - Manual

FINISHING AND REFINISHING INSTRUCTIONS
for Interior and Exterior Door Slabs and Systems (JCM004)
The information contained herein is provided solely for informational and/or educational purposes. JELD-WEN disclaims any and all liability associated with the use and/or
provision of this information. Any reliance upon the information or advice is at the risk of the party so relying.
©2014 JELD-WEN, inc.; This publication and its contents are owned by JELD-WEN, inc. and are protected under the U.S. Copyright Act and other intellectual
property laws. All trademarks, service marks, logos and the like (whether registered or unregistered) are owned or controlled by JELD-WEN, inc. or others.
Unauthorized use or duplication of JELD-WEN intellectual property is prohibited.
JELD-WEN reserves the right to change product specifications without notice. Please check our website, jeld-wen.com, for current information.
Read all instructions thoroughly before beginning. This is a guideline
for painting and finishing exterior and interior doors. JELD-WEN cannot
evaluate all available paints, stains, or application requirements. Consult
a paint professional or a local paint department/store for coatings
best suited to the project. Select top quality finishes and follow all
manufacturers' instructions.
Finish all six surfaces (both sides and edges) of the door slab, including
cutouts for hardware (if hinges are installed on an interior door slab,
do not remove them), as well as the frame and the brickmould or other
trim to ensure proper protection from the elements. The sweep on the
bottom of exterior doors needs to be sealed on both ends with exterior
silicone sealant and should not be painted or stained. The sweep should
not be removed as paint or stain application to the rail underneath is not
recommended. Failure to finish the door slab as instructed may result in
the denial of warranty claims for operational or performance problems.
IMPORTANT!
• Steel and fiberglass door slabs MUST be finished within thirty (30)
days of purchase.
• Factory primed wood doors (molded, flush, custom carved, stile and
rail) MUST be finished within fourteen (14) days of purchase.
• Raw, un-primed wood doors (molded, flush, custom carved, stile and
rail) MUST be finished within SEVEN (7) days of purchase.
• Finish wood frames in the same manner as the slab.
• Vinyl components do not require finishing.
• Refinish products when the finish cracks, splits or becomes dull.
NEEDED MATERIALS AND TOOLS
When preparing to finish doors, consider the materials and tools required for
the entire project. Listed below are some common items needed to properly
finish doors. Not all materials and tools will be required for every job.
(08/14)
BASIC FINISHING RECOMMENDATIONS - CONTINUED
• Allow doors to acclimate to local conditions for at least 24 hours
before finishing.
• Remove all hardware (except hinges from an interior door slab) and
mask off glass, weatherstrip, and the door sweep (on the bottom of
exterior slabs).
• Finish in dust free area away from direct sunlight.
• Finishing is easier if the slab is in a horizontal, flat position on a
padded surface. This is not required and the slab may be finished in
any position, however, do not stand an exterior slab on the sweep
(the weatherstrip on the bottom of the door) as damage may result.
• If finishing an exterior slab, seal both ends of the sweep (weatherstrip
on the bottom) with an exterior grade silicone.
• If finishing a slab with a glass insert, inspect for sealant that may have
squeezed out onto the glass or door. Carefully score excess sealant (do not
scratch glass) with a utility knife (stainless steel blade) and remove with a
plastic putty knife.
• If finishing a slab with a glass insert, follow the glass manufacturer's
instructions on the glass insert frame label.
• Door must be clean and dry before finishing.
• Test your finish prior to application in a discreet location.
• Apply finish materials in multiple light coats instead of fewer heavy coats.
• If painting grained or textured doors, too many coats will diminish
the wood grain texture.
CHOOSE FINISHING MATERIALS
• If the door is exposed to direct sunlight, dark colored finishes may
fade or deteriorate quickly and increase maintenance. See our
Appropriate Protection document at www.jeld-wen.com in the
Product Support section under Care and Maintenance for more
information on color choice.
• Use a good quality primer and paint, or wood sealer and stain.
We recommend using one manufacturer's products to ensure
compatibility. Follow all manufacturers’ application instructions.
• If choosing an oil or solvent based paint, consult with a paint
professional on the best product (usually quick drying) for the job.
• If staining fiberglass doors, for the best results, we recommend using our
Stain Kit. If not possible, use only a professional quality, heavy body or
highly viscous exterior gel stain. Note: Once Architectural fiberglass doors
are stained, it is very difficult to change the color. Always test the color
in an inconspicuous area to determine if the color is acceptable before
staining the entire door.
• Use only exterior solid color stains on wood surfaces exposed to
sunlight because their high concentration of pigments protects wood
against damage. The natural wood color and grain is obstructed,
but the wood texture is retained. These stains provide minimum
protection against water or dirt protection, so a polyurethane top
coat must be used.
• Finish with coatings that are resistant to water, wear, heat, solvents
and chemicals. Without these characteristics, the finished product
may deteriorate, compromising its integrity.
• Use a topcoat containing UV inhibitor. Use exterior finishing products
on all exterior surfaces as well as for interior surfaces still exposed to
sunlight to provide extra protection and durability.
Needed Materials and Tools:
• Safety glasses and rubber
gloves
• Screwdrivers
• Power drill
• Hammer
• Punch
• Utility knife
• Plastic putty knife
• Hand block sander
• Foam brush
• Paint brush
• Sprayer
• Vinegar and water
• Denatured alcohol
• Wood block
• Masking tape
• Sandpaper - 150-220 grit or
finer
• Pre-stain conditioner if
staining wood
• Clean rags
• Cheesecloth
• Polyurethane
• Stain Kit (Fiberglass Doors)
• Paint or stain (see instructions
for each door type for specific
recommendations)
• Paint thinner or mineral spirits
(for clean up)
• Tack cloth
• 0000 Steel wool
BASIC FINISHING RECOMMENDATIONS
• Wear safety glasses for eye protection, and rubber gloves to prevent
soiling the door with oil from hands.