Manley JUMBO SHRIMP - Manual (Page 18)

How to change the user-numbers and re-pair the system:
Ordinarily there will seldom be a need to change the user-number. Changing the user-number requires a few
more ballet steps, as listed below. Some steps are time-window sensitive to help prevent pairing errors due to
interference from other signals on the radio channel.Please read over the list of required actions and LED reac-
tions completely before attempting to reprogram your Remora system user-number.
1. Make sure the Jumbo Shrimp is plugged into the mains power line, but turned off, and make sure that the
battery in the Remora Remote transmitter is healthy.
2. Put the Remora Remote into the programming mode by pressing the up and down buttons simultaneously
for about a half second. The LED will blink yellow to indicate that it is in programming mode.
3. While the LED is blinking yellow, enter the new user-number by tapping the “UP” button 1 to 7 times,
followed by pressing the “DOWN” button 1 to 7 times. Example: 3 “ups” and 2 “downs” will set a new user-
number to (3,2). After it has accepted your new code, yellow blinking LED will stop blinking and will then
read back the new user-number you set by displaying 3 GREEN blinks followed by 2 RED blinks. BE CARE-
FUL NOT to touch the buttons once the read-back has happened; the remote knows you have reprogrammed
it, and it is “armed” with a special data string to tell the receiver-decoder that a user-number change has hap-
pened.
4. With the Remora Remote in this “armed” state and with it in your hand with your thumb hovering over
either button, power on your Jumbo Shrimp Preamplifier by turning the power switch to the “ON” position.
Once the preamplifier’s badge lamp is lit, you have about 1.5 seconds to press either button on the remote. The
preamplifier should now respond by rotating the volume control in the direction of which ever button has been
pressed. Pairing is now complete.
For the first 1.5 seconds after power-up, the Jumbo Shrimp Preamplifier’s receiver-decoder is configured to be
in programming mode looking for any new user-number changes. If the decoder detects the new user-number
programming string from an “armed” remote during this 1.5 second interval, the decoder will immediately
discard the old user-number and adopt the new one before resuming normal operation.
In the event that you lose or damage your Remora Remote, a new one can be supplied pre-programmed with
your user-number if you provide it to us. Otherwise, it is a straightforward matter to observe, note, and re-pair
the Remora Remote’s user-number to the preamplifier using the query and programming procedure described
earlier.
Please direct any comments or questions to your dealer or to Manley Labs for further assistance.
** FCC STATEMENT **
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
18