BBK Performance 5010 - Manual (Page 2)

INS-103
w w w . B B K P E R F O R M A N C E . c o m
IMPORTANT- All appropriate safety equipment(i.e: gloves,tools) must be used during the installation of these product(s).
BBK Performance, Inc. accepts no responsibilty for injuries resultisng in the installation of any product(s).
MORE ON
THE BACK
STEP 15 Assemble the fuel pressure regulator mount and your choice of regulator using the 3 supplied
screws and regulator- to- mount gasket.
STEP 16 Place one of the supplied O-rings into the groove in the bottom of the regulator mount and
install the fuel pressure regulator/ mount assembly onto the rear of the passenger side rail. Fasten it to
the rail using the supplied 6-32 x 3/4” screws.
STEP 17 Place the remaining O-ring over the fuel rail end cap and push the cap into the front end of
the driver side rail. Secure it using the remaining 10-32 x 5/8” button head screw.
STEP 18 Thread the 1 of the supplied 90° fittings into the rear of each fuel rail until snug. Then con-
tinue tightening until the outlets will face each other once the rails are installed.
STEP 19 Push one end of the supplied crossover hose fully onto one of the 90° fittings.
STEP 20 Thread the long pre-assembled hose into the regulator mount until its snug. Then tighten it
until it is following the rail forward to meet up with the stock fuel return line.
STEP 21 Thread the short pre-assembled hose into the front end of the passenger side rail until its
snug. Then tighten it until it is pointing towards the passenger side of the car to meet up with the stock
fuel feed line.
STEP 22 Insert the injectors into the rails (we recommend lightly lubricating the outsides of each
O-ring to ensure proper seating).
STEP 23 (Follow for both rail/injectors assemblies) carefully guide each injector into its injector port
on the lower manifold. Tighten the supplied fasteners through the fuel rail mounting tabs and into the
lower manifold.
STEP 24 Determine the proper length for the crossover hose and cut it to fit. Push the cut end fully
onto the other 90° fitting (if necessary, rotate the fittings to line up.)
STEP 25 Connect the spring lock fittings on the fuel rails and regulator to the stock fuel feed and return
lines.
TESTING THE FUEL RAILS FOR LEAKS
TO AVOID SHOCK/ FIRE/WORSE, WE STRONGLY RECCOMEND FOLLOWING THE
INSTRUCTIONS FOR THE NEXT PROCEDURE CLOSELY!
STEP 26 Disconnect the electrical connector from the ignition coil (this may require removing the
plastic cover located between the battery and the strut tower).
STEP 27 If the car has automatic door locks or an alarm, be sure to leave the driver door open while
following this step. Otherwise the doors might lock with the key in the ignition). With the negative bat-
tery cable disconnected turn the ignition key to the on position. While watching the fuel rails and con-
nections, touch the negative battery cable to the negative terminal of the battery for 3 seconds then
stop. (This will turn the fuel pump on momentarily and pressurize the fuel rails. If you have any
leaks in the connections or fittings this will allow you to find and repair them before you put the
upper intake manifold back on). Once you have verified that there are no fuel leaks in your system
turn the key back to off.
STEP 28 Re-install the upper intake manifold and re-establish all electrical, coolant, vacuum, and cable
connections at the throttle body, EGR valve, IAC valve, ignition coil, and the upper intake manifold.
STEP 29 If you followed STEP 3; re-install the lower cup, rotor, cap, and distributor wires.
STEP 30 Connect the intake hose between the mass air meter and throttle body.
STEP 31 Re-connect the negative battery terminal.