BBK Performance 1758 User Manual

BBK Performance For the car

Advertising

‘04-06 4.6L F150 3V Throttle Body Part #1758

‘05-07 Mustang 4.0L V6 Throttle Body Part # 1765

w w w . B B K P E R F O R M A N C E . c o m

I N S T A L L A T I O N

I N S T R U C T I O N S

ATTENTION!

All BBK throttle bodies are pre adjusted and tested during assembly.
If you have any problems with this throttle body call our Tech Support
hotline at (951)296-1771 or e-mail

DO NOT ATTEMPT TO MAKE ANY ADJUSTMENTS!

TOOLS REQUIRED

1/4” Ratchet

T-20 Torx

1/4” Extension Needle nose pliers
8mm socket & 10mm Deep socket 5mm Allen Wrench

STEP 1

Disconnect negative battery terminal. If these instructions are followed closely, this will

prevent the CHECK ENGINE light from coming on after the installation.
STEP 2 Disconnect the PCV tube by gently twisting the green locking tab and pulling the tube away from
the inlet hose. Loosen the hose clamp at the throttle body. Pull the inlet hose away from the throttle body
and set it aside.
STEP 3 Unplug the throttle body electric motor and TPS by sliding the red colored locking clips back, and
then squeezing the tabs on each wiring connector while pulling them from their connections.

Note: Some 2005 V-6 Mustangs have 2 water hoses that route through the stock throttle body.
On those models, disconnect the water hoses and bypass them by connecting them to the supplied
U-shaped tube using the original clamps. The U-shaped tube is not used for any other vehicles.

STEP 4 Unbolt and remove the throttle body

Note: Be careful not to damage the throttle body motor

housing as you will be re-using it.
STEP 5 Using the T-20 Torx remove the motor housing, plastic capped spring, and TPS from the stock
throttle body.

Note: plastic capped spring will be under tension load. You will be re-loading the

spring in STEP 11. When removing the TPS, pull it straight off of the throttle body. Do not twist or
rotate the TPS.
STEP 6 Pop the removable circular cap off of the motor housing (

WKLVLVHDVLO\GRQHZLWKDÀQJHU)

STEP 7 Place the plastic capped spring over the end of the throttle shaft of the BBK throttle body and line
the pigtail hook on the spring up with the catch slot in the gear.
STEP 8 Install the motor housing minus the removable cap onto the BBK throttle body over the plastic
spring cap and tighten screws.
STEP 9 Using needle nosed pliers rotate the plastic spring cap

COUNTER CLOCKWISE (approximately

180°) until the 2 tabs line up with their matching landings in the motor housing, then gently pull up on the
cap until it pops up into a latched position.
STEP 10 Align the tabs on the removable cap with the slots on the motor housing and snap it into place.
STEP 11 Install the TPS onto the BBK throttle body by lining up the locating tab and tightening the
screws.

The TPS does not need to be rotated or “clocked”.

STEP 12

&KHFNWKHWKURWWOHERG\IRUVPRRWKDFWLRQE\RSHQLQJDQGFORVLQJWKHÁDSDIHZWLPHVZLWK\RXU

ÀQJHUV<RXVKRXOGIHHODVOLJKWGUDJIURPWKHHOHFWULFPRWRUEXWLWVKRXOGQHYHUELQGXSRUVWLFN
STEP 13 Install the throttle body (use supplied gasket on 1758) onto the intake manifold using the 4 sup-
plied screws.
STEP 14 Re-install the intake hose and re-attach the PCV tube.
STEP 15 Connect negative battery cable.