Monoprice 5082 Wall Mount Bracket - Manual

FIX TO WALL
FIT SCREEN
2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the TV Rails (b and c) are mounted at
an equal distance from the top of the TV and as close to the center as possible as shown in diagram 2-A. Safety screws
should face the outside of the television. M4, M5, M6 and M8 bolts are provided. Plastic Spacers (l) are provided for use
with M4, M5, M6 and M8 TV mount bolts on TV's with curved or recessed back panels as shown in diagram 2-B. If you are
mounting to a television with a flat back you will not need a plastic spacer as shown in diagram 2-C. Make sure these bolts
are right! Some televisions have shallow threaded inserts; we have provided 4 extra washers you may use to offset this if
the provided bolts are too long.
a b x1 c d
e f
Wall Plate
x1
Left TV Rail
x1 x12
M4/M5/M6
Washer
8mm Lag Bolt Concrete Anchor
x6 x6
M4x30mm
Machine Screw
M5/M6/M8
Washer
Plastic spacer
M8x25mm
Machine Screw
i k
l m
x4 x10
x4 x4 n o
q
M8x40mm
Machine Screw
M5x30mm
Machine Screw
M6x30mm
Machine Screw
x4
x4 x4
ASSEMBLY INSTRUCTIONS
FOR FIXED FLAT PANEL WALL MOUNT
HANG ONTO THE WALL
Right TV Rail
TV Mounting Hole
k or d
k or d
l
TV Mounting Hole
k or d
TV Rail 2-B 2-C
TV Rail
Level with Top
Close to centered
2-A
Wall
a
c
3-A
TV
4-A 4-B
This product is designed to mount flat panel televisions weighing up to 75kgs to a vertical firm wall.
Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper
installation may cause damage or serious injury.
Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an
expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The
supplied hardware is not for steel.
Forbidden Instruction: Do not mount onto plasterboard or paneled walls.
S U P P L I E D PA R T S : S u p p l i e d j o i n t p a r t s a r e e x c l u s i v e f o r u s i n g i n t h i s p r o d u c t .
O t h e r j o i n t p a r t s a r e f o r b i d d e n t o u s e o n t h i s p r o d u c t . I f a n y p a r t s a r e m i s s i n g
o r f a u l t y, t e l e p h o n e t h e s p e c i a l f r a n c h i s e r f o r a p l a c e m e n t .
1a.SOLID BRICK AND CONCRETE BLOCK MOUNTING: Use the Wall Plate (a) as a template to mark
6 holes locations on the wall. The outer holes must fall to outside of the two large holes in the middle of the plate.
Three in the top row slots and three more in the bottom row. Make sure these holes are level and there is at least
200mm between any two holes. Pre-drill these holes with a 10mm masonry bit to at least 90mm in depth. Insert a
Concrete Anchor (f) into each of these holes. Attach the Wall Plate to the wall using 6 Lag Bolts (e) and 6 M4 / M5
/ M6 Washers (d).
3. HANG THE TV ONTO THE WALL PLATE:
First hook the TV Rails (b and c) over the top of the Wall
Plate (a) as showed in diagram 3-A.
Then tighten the Safety Screws as showed in diagram 3-B.
Diagram 4-A: Front view of the fixed plasma mount
assembled.
Diagram 4-B: Safety screws tightened.
Please check whether screws are fixed well each two months.
IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT OUR SPECIAL
FRANCHISER.
TENDING INSTRUCTION
Note:This product should be mounted to solid brick, concrete or hard wood
batten/studs wall.
1b.HARD WOOD WALL MOUNTING: The Wall Plate (a) MUST to be mounted to two wood studs. Use a high quality
stud sensor to locate three adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail
shown in diagram 1-A. Pre-drill a 80mm deep hole at the desired height in each stud using a 6mm drill bit. Use the Wall
Plate as a template to mark the location of the second hole in each stud. Attach the Wall Plate to the wall using the 4 Lag
Bolts (e) and 4 M4 / M5 / M6 Washers (d). Make sure the Wall Plate is oriented so the flat surface in the center of the
plate in against the wall shown in diagram 1-B.
Note: Do not use any concrete ancher when you mount the bracket onto hard wood wall.
Diagram 1-A
Diagram 1-B