Monoprice 7057 Wall Mount Bracket - Manual

FIX TO WALL
①
FIT SCREEN
②
2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the TV Rails (b and c) are mounted at
an equal distance from the top of the TV and as close to the center as possible as shown in diagram 2-A. Safety screws
should face the outside of the television. M4, M5, M6 and M8 bolts are provided. Plastic Spacers (l) are provided for use
with M4, M5, M6 and M8 TV mount bolts on TV's with curved or recessed back panels as shown in diagram 2-B. If you are
mounting to a television with a flat back you will not need a plastic spacer as shown in diagram 2-C. Make sure these bolts
are right! Some televisions have shallow threaded inserts; we have provided 4 extra washers you may use to offset this if
the provided bolts are too long.
a b x1 c d
e f
Wall Plate
x1
Left TV Rail
x1 x4
8mm Lag Bolt Concrete Anchor
x4 x4
M4x30mm
Machine Screw
M5/M6/M8
Washer
Plastic spacer
M8x25mm
Machine Screw
i k
l m
x4 x4
x4 x4 n o
q
M8x40mm
Machine Screw
M5x30mm
Machine Screw
M6x30mm
Machine Screw
x4
x4 x4
ASSEMBLY INSTRUCTIONS
FOR FIXED FLAT PANEL WALL MOUNT
HANG ONTO THE WALL
③
Right TV Rail
TV Mounting Hole
k
l
TV Mounting Hole
k
TV Rail 2-B 2-C
TV Rail
Level with Top
Close to centered
2-A
Wall
a
c
3-A
TV
4-B
This product is designed to mount flat panel televisions weighing up to 75kg to a vertical firm wall.
Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper
installation may cause damage or serious injury.
Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an
expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The
supplied hardware is not for steel.
Forbidden Instruction: Do not mount onto plasterboard or paneled walls.
SUP PL I ED PART S: Su p p l i e d j o i n t p a r t s a r e e x c l u s i v e f o r u s i n g i n t h i s p r o d u c t .
Ot h e r j o i n t p a r t s a r e f o r b i d d e n t o u s e o n t h i s p r o d u c t . I f a n y p a r t s a r e mi s s i n g
o r f a u l t y, t e l e p h o n e t h e s p e c i a l f r a n c h i s e r f o r a p l a c e men t .
SOLID BRICK AND CONCRETE BLOCK MOUNTING: Use the Wall Plate (a) as a template to mark
4 holes locations on the wall. two in the top row slots and two more in the bottom row. Make sure these holes are
level and there is at least 110mm between any two holes. Pre-drill these holes with a 10mm masonry bit to at
least 60mm in depth. Insert a Concrete Anchor (f) into each of these holes. Attach the Wall Plate to the wall using
4 Lag Bolts (e) and 4 M4 / M5 / M6 Washers (d).
3. HANG THE TV ONTO THE WALL PLATE:
First hook the TV Rails (b and c) over the top of the Wall
Plate (a) as showed in diagram 3-A.
Then tighten the Safety Screws as showed in diagram 3-B.
Diagram 4-A: Front view of the fixed plasma mount
assembled.
Diagram 4-B: Safety screws tightened.
Please check whether screws are fixed well each two months.
IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT OUR SPECIAL
FRANCHISER.
TENDING INSTRUCTION
Note:This product should be mounted to solid brick, concrete or hard wood
batten/studs wall.
4-A
Washer
f
e
d