Checkers Guard Dog 1 Channel Low Profile with Standard Ramps - Manual

ASSEMBLY:
• Inspect areas for safety hazards
• Assemble sections by aligning female connectors over male connectors
• Press with foot to secure female connectors to male connectors
• Open cover and install cables down into channels
• Close cover flush with base
• Test installation for intended use
• Periodically inspect installation
ASSEMBLY INSTRUCTIONS
#ZIS-GDLP-ST
Ver: 2/11
NO. OF
CHANNELS
5 Channel 24,000 lbs. (10,886 kg)
MAXIMUM LOAD PER TIRE
70 ˚ F (21 ˚ C)
48,000 lbs. (21,772 kg)
3 Channel 17,000 lbs. (7,711 kg) 34,000 lbs. (15,422 kg)
2 Channel 13,000 lbs. (5,896 kg) 26,000 lbs. (11,792 kg)
1 Channel 13,000 lbs. (5,896 kg) 26,000 lbs. (11,792 kg)
MAXIMUM LOAD PER AXLE
70 ˚ F (21 ˚ C)
CABLE/HOSE MANAGEMENT COMPONENTS
Simply interlock with
Dog Bone connectors to
extend protection length.
Before installing, ensure circular recessed
areas are free from dirt and debris. Apply
2-3 drops of Checkers Super Glue to the
top of the center post and then place a bead
of glue around the outer edge of the half
moon area. Align rubber pad slot with rib
on Cable Protector, then quickly place
Rubber Pad over the post and slot on cable
protector. Firmly push down with thumb
around the outer edge of Rubber Pad until
fully seated. Repeat until complete.*
RUBBER PAD INSTALLATION
* For your safety, please wear safety glasses and
rubber gloves. Checkers Super Glue is best when
stored refrigerated.
1) Before installing, clean bottom edges of cable protector with a
dry rag. 2) Apply a generous bead of Checkers Super Glue to the
bottom edge of the cable protector (parallel with outer edge). 3)
Quickly place one end of the VELCRO® brand fastener over the
bead of glue, lay the VELCRO® brand fastener strip
down, and apply pressure.
4) Repeat this step for
other side of cable
protector. Trim excess
strip with a razor
blade.*
CARPET KIT INSTALLATION
1 2 3
NOTE:
Optional Anti-Slip Rubber Pads
and Carpet Kits with VELCRO
®
Brand Fasteners can be purchased
and easily installed on Guard Dog
Low Profile Cable Protectors with
Standard Ramps
(see instructions below).
5 CHANNEL STANDARD
3 CHANNEL STANDARD
2 CHANNEL STANDARD
1 CHANNEL STANDARD
CHANNEL CAPACITY - MAX. DIAMETER INCHES (mm)
5 Channel Center channel: 1.6 in. (40.6 mm) width x .75 in. (19.0 mm) height
Other 4 channels: 1.3 in. (33.0 mm) width x .75 in. (19.0 mm) height
3 Channel Center channel: 2 in. (50.8 mm) width x .75 in. (19.0 mm) height
Other 2 channels: 1.25 in. (31.8 mm) width x .75 in. (19.0 mm) height
2 Channel 1.5 in. (38.0 mm) width x .75 in. (19.0 mm) height
1 Channel 2.25 in. (57.2 mm) width x .75 in. (19.0 mm) height
HEAVY DUTY LOW PROFILE
1, 2, 3 or 5 CHANNEL SYSTEMS
WITH STANDARD RAMPS
LOW PROFILE PROTECTORS
®
CPRPKIT.75-20 Optional Anti-Slip Rubber Pad Kit for all Guard Dog Low Profile Protectors WITH Standard Ramps (includes 20 anti-slip rubber pads)
CPGLUE 1/2 oz Bottle of Checkers’ Clear Super Glue (best if kept refrigerated). Use for permanent application of Anti-Slip Rubber Pads
CPCARPETKIT-3
Optional Carpet Kit with VELCRO® Brand Fasteners for all Guard Dog Low Profile Protectors WITH Standard Ramps
(includes two 37" x .25" black VELCRO® brand fastener strips and a 1/2 oz Bottle of Checkers’ Clear Super Glue (CPGLUE)
OPTIONAL TRACTION KITS
LOAD CAPACITY:
The Cable/Hose
Protection System has different load
supporting capabilities depending on type of
vehicle and temperature. Suitability must be
verified by testing under actual conditions.
CHANNEL CAPACITY:
OPERATING TEMPERATURE:
-40˚F to 120˚F (-40˚C to 48˚C)
CHEMICAL RESISTANCE:
Tested
for compatibility with common motor oils,
gasoline and diesel fuel. Limited resistance
to brake fluids and other chemicals.
MATERIAL:
UV-stabilized
polyurethane elastomer