Checkers Powerback Rubber Duct Protectors User Manual
Rubber duct protectors, Assembly instructions, Carpet kit installation
• Inspect areas for safety hazards
• IF cable/cord has an end that is small enough to fit through the channel, insert end
into channel and push it through to the other side.
• IF cable/cord has an end that is too large to fit through the channel, a utility knife
can be used to carefully cut through the groove on the underside of the protector.
Then insert the cable/cord into the channel through the slit on the underside.
• Assemble sections by aligning protectors.
• Select models can be securely attached to one another with connector pegs. To do
so, simply align connector pegs with holes on the end of the cable protector and
push in firmly to secure them. Then
align second protector with pegs and
firmly push the two cable protectors
together (see illustration). Repeat this
procedure to connect as many rubber
duct protectors as needed.
• Test installation for intended use
• Periodically inspect installation
ASSEMBLY INSTRUCTIONS
#ZIS-RFD
Ver: 2/11
RUBBER DUCT
PROTECTORS
• All Powerback Protectors are shipped unslit on the bottom except models RFD7, RFD8, and RFD9. • All Powerback Protectors feature ribbed underside to prevent slipping.
1/4"
1/2"
1/8"
6 "
1
1
/
2
"
1
7
/
8
"
Note: this drawing is
rendered at a different
scale than RFD1 - RFD6.
Optional Connector Kit Available (RFDCN-1/2)
RFD9
RFD8
1/4"
1/2"
6 "
1
1
/
4
"
1
5
/
8
"
1/8"
Note: this drawing is
rendered at a different
scale than RFD1 - RFD6.
Optional Connector Kit Available (RFDCN-1/2)
RFD7
Note: this drawing is
rendered at a different
scale than RFD1 - RFD6.
1/2"
1"
5
3
/
4
"
1
3
/
8
"
1/4"
1/8"
Optional Connector Kit Available (RFDCN-1/2)
RFD6
1/2"
7/8"
3/4"
5
3
/
4
"
1
1
/
8
"
Optional Connector Kit Available (RFDCN-1/2)
RFD5
3/8"
7/16"
3/4"
3/4"
4
1
/
2
"
1"
Optional Connector Kit Available (RFDCN-3/8)
RFD4
3/8"
1"
3
1
/
4
"
1"
3/4"
Optional Connector Kit Available (RFDCN-3/8)
RFD1
3"
7/16"
1/4"
1/2"
RFD2
3"
7/16"
1/4"
7/16"
RFD3
1/2"
3
1
/
2
"
3/4"
5/16"
1/2"
3/4"
* For your safety, please wear safety glasses and rubber gloves.
Checkers’ Super Glue is best when stored refrigerated.
1) Before installing, clean bottom edges of cable protector with a
dry rag. 2) Apply a generous bead of Checkers’ Super Glue to the
bottom edge of the cable protector (parallel with outer edge). 3)
Quickly place one end of the VELCRO® brand fastener over the
bead of glue, lay the VELCRO® brand fastener
strip down, and apply
pressure. 4) Repeat this
step for other side of
cable protector. Trim
excess strip with a
razor blade.*
CARPET KIT INSTALLATION
1
2
3
OPTIONAL CARPET TRACTION KITS
CPCARPETKIT-5
CPCARPETKIT-10
Optional Carpet Kit for All 5 ft Powerback Models - Includes two 61" x .25" Black VELCRO® brand fastener strips and a 1/2 oz Bottle of Checkers’ Clear Super Glue (CPGLUE)
Optional Carpet Kit for All 10 ft Powerback Models - Includes two 61" x .25" Black VELCRO® brand fastener strips and a 1/2 oz Bottle of Checkers’ Clear Super Glue (CPGLUE)
Connector Pegs