State Shingle Roof - Manual

1
SPANNER MOUNTING
Although there are other installation methods for mounting
solar collectors, it has been determined that the spanner
mounting method is the most suitable for this application.
Consult with your installer if other mounting means are
required for your installation.
1. After locating the mounting points from Figure 1 for
vertical mounting, Figure 2 for horizontal mounting,
and Table 1, layout the roof as specified and drill 5/16”
holes between the rafters where indicated.
2. Insert the flashing so the top part is under the next row
of shingles and the flashing hole/grommet aligns with
the mounting hole. See Figure 3.
3. The compression bracket washer is positioned over the
flashing seal with the concave side towards the seal.
See Figure 4.
4. The mounting bracket is then placed on the compression
bracket washer.
5. A 12” length of stainless steel 5/16” all-thread is then
inserted through the hole and a stainless steel nut, lock
washer, and EPDM bonded washer secures the all-
thread to the mounting bracket. The all-thread should
extend about 4” below the roof rafters.
6. Fabricate spanners, one for each mounting bracket,
using a 2” x 4” or similar lumber. Spanners must be
long enough to span at least two rafters. In the attic or
crawl space drill a 5/16” hole through each spanner and
insert the all-thread through it. Secure each spanner to
the rafters with decking or wood screws. See Figure 4.
7. Fabricate spacer blocks, one for each mounting bracket,
using a 2” x 4” or similar lumber the same width of the
rafter next to each all-thread. Place spacer blocks next
to the all-thread between the spanner and roof. Secure
each spacer block to the spanners with decking or
wood screws. Spacer blocks are necessary to avoid
deformation of the roof. See Figure 4.
8. With a stainless steel nut, lock washer and fender
washer secure the all-thread to each spanner. Tighten
down until the mounting bracket is tightly secured
to the roof (approx. 97 inch pounds). Be careful not
to overtighten and dish out the roof underneath the
mounting bracket.
9. Repeat steps 2-8 for the remainder of the mounting
bracket locations.
125 Southeast Parkway, Franklin, TN 37068
PHONE: 1-800-433-2545 • FAX: 1-800-433-2515
SOLAR COLLECTOR SHINGLE ROOF MOUNTING INSTRUCTIONS
BASIC TOOLS AND MATERIALS
Drill & Drill Bits
Saw (Hand or Circular w/Extension Cord)
Tape Measure
Chalk Line
Utility Knife
Level
Pliers
8” & 10” Adjustable Wrenches
7/16” & 9/16” Wrenches
Ratchet
7/16” & 9/16” Sockets
6’ x 8’ or 6’ x 10’ Tarp (1 per collector)
10 linear feet of 2” x 4” or 2” x 6” lumber for spanner
mounting per number of collectors in the system
Installation Hardware (Supplied):
Includes:
• Hardware & Mounting Brackets
PRINTED 0311 319198-001
structural members of the roof with the stainless steel hardware
provided. The solar collector must be attached to the mounting
hardware as detailed in Figure 5.
Preserving the integrity of the roof membrane is the
most important roofing consideration. Ensure that all roof
penetrations required to plumb and mount the solar collector
are properly flashed and sealed in accordance with standard
roofing practices.
If the region is subject to hurricane conditions, additional
steps may be required to secure the collector and mounting
hardware to the structural members. In certain areas of the
country, local building codes may require collector wind load
testing or prescribe specific mounting procedures. Consult
your local building department.
Install the collectors as described in the Spanner Mounting
instructions.
CAUTION
ALL PERSONS WORKING ON ROOFS SHOULD
HAVE SUCCESSFULLY COMPLETED A FALL SAFETY
COURSE AND SHOULD BE PROPERLY EQUIPPED
WITH THE APPROPRIATE SAFETY EQUIPMENT
AFTER COMPLETION OF THE COLLECTOR
MOUNTING AND PRIOR TO SYSTEM CHARGING THE
COLLECTORS MUST BE COVERED BY A BLANKET OR
OTHER MEANS TO AVOID SOLAR RADIATION FROM
HEATING THE COLLECTORS. THE SURFACES OF THE
COLLECTOR CAN BECOME EXTREMELY HOT AND
COULD POSE A BURN HAZARD.
WARNING
The most important structural consideration is to securely
anchor the solar collector and the mounting hardware to the