Red Lion CUB7T User Manual

Description, Safety summary, Specifications

Advertising
background image

1

1.64 (41.6)

0.87

(22.1)

1.10

(27.9)

2.00 (50.8)

2.17 (55)

With Wires

With Terminal Block

l

0.35" (8.9 mm) HIGH LCD DIGITS, REFLECTIVE OR TRANSMISSIVE

WITH YELLOW/GREEN OR RED BACKLIGHTING (6-26 VDC power

supply required for version with LED backlighting)

l

INTERNAL LITHIUM BATTERY PROVIDES UP TO 7 YEARS OF

TYPICAL UNINTERRUPTED OPERATION

l

COUNT SPEEDS UP TO 10KHZ

l

9 PROGRAMMABLE TIME RANGES

l

CONTACT, LOGIC, OPEN COLLECTOR, OR HIGH VOLTAGE INPUTS

l

STANDARD WIRE CONNECTIONS OR OPTIONAL PLUG-IN TERMINAL

BLOCK

l

NEMA 4X/IP65 SEALED FRONT BEZEL THAT FITS 1/32 DIN CUT-OUT

DESCRIPTION

The CUB7 series is an 8-digit lithium battery powered miniature counter or

timer with large 0.35" (8.9 mm) high digits. It has an LCD read-out available in

Positive Imagine Reflective, Negative Image Transmissive with yellow/green or

red backlighting. The backlight versions require an external 6-26 VDC power

supply. The CUB7 series is housed in a lightweight, high impact plastic case

with a clear viewing window. The sealed front panel with silicon rubber keypad

meets NEMA 4X/IP65 specification for wash-down and/or dusty environments,

when properly installed with supplied panel gasket and mounting clip.

Both counter and timer CUB7 models are available with a low voltage input

(28 VDC max) or an isolated high voltage input (50-250 VDC/VAC). The low

voltage input has DIP switch selections for SINKING or SOURCING along

with a HIGH/LOW FREQUENCY selection (low frequency for contact inputs).

Both units have front panel keypads that can be used to reset the display. The

keypad can be enabled/disabled via a single DIP switch. The standard unit uses

22 gauge wires for external connections, an optional plug-in terminal block is

available.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the

literature or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

SPECIFICATIONS

1. DISPLAY: 8-digit LCD, 0.35" (8.90 mm) high digits

2. POWER: Non-replaceable internal 3.6 VDC lithium battery provides 7 years

of typical continuous operation (high count speeds in SNK mode & extreme

ambient temperatures will decrease battery life, use of SRC mode can extend

battery life)

OPTIONAL LED BACKLIGHT POWER: 6-26 VDC @ 25 mA max.

Must use an NEC Class 2 or Limited Power Source (LPS) rated power supply.

Note: External power shall incorporate disconnecting device (switch or circuit

breaker) and provide Double/Reinforced isolation from MAINS supply.

3. LOW VOLTAGE INPUT:

COUNTERS: CUB7CCS0, CUB7CCR0, CUB7CCG0

SNK mode (DIP switch 1 off, internal pull-up to battery)

V

IN

High Min = 1.25 VDC; V

IN

Low Max = 0.45 VDC

I

IN

Max = 8 µA; V

IN

Max = 3.6 VDC

Count Speed: (count on negative edge)

High freq mode (DIP switch 2 off): max 5 kHz @ 50% duty cycle

Low freq mode (DIP switch 2 on): max 30 Hz @ 50% duty cycle

Note: The three models listed above may be used for count inputs with

10-50 VAC signals when using a VCM10000 converter module. DIP

switches must be set for SNK and Low frequency.

SRC mode (DIP switch 1 on, internal 20 kW pull-down to common)

V

IN

High Min = 1.25 VDC; V

IN

Low Max = 0.45 VDC

I

IN

Max = 5 mA; V

IN

Max = 28 VDC

Count Speed: (count on negative edge)

High freq mode (DIP switch 2 off): max 10 kHz @ 50% duty cycle

Low freq mode (DIP switch 2 on): max 50 Hz @ 50% duty cycle

TIMERS:

Models: CUB7TCS0, CUB7TCR0, CUB7TCG0 For these models, the

unit will time when the CUB7 input is low.

SNK mode (DIP switch 1 off, internal pull-up to battery)

V

IN

High Min = 1.25 VDC; V

IN

Low Max = 0.45 VDC

I

IN

Max = 8 µA; V

IN

Max = 3.6 VDC

Note: The three models listed above may be used with 10-50 VAC

MODEL CUB7 – MINIATURE ELECTRONIC 8 DIGIT COUNTER or TIMER

DIMENSIONS In inches (mm)

Note: Recommended minimum clearance (behind the panel) for

mounting clip installation is 2.1" (53.4) H x 5.5" (140) W.

Bulletin No. CUB7N-D
Drawing No. LP0825
Released 09/12

Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net

C

US LISTED

UL

R

3RSD

PROCESS CONTROL EQUIPMENT

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

Advertising
This manual is related to the following products: