Red Lion ZHG - STANDARD & HEAVY DUTY - Manual (Page 4)

The Length Sensor Hinge Clamp Assembly provides an easy method for
attachment and mounting of the Length Sensors and LSCB1 Conversion
Bracket. The removable top on the solid zinc LSAHC mounting block
allows quick installation of the Length Sensor handle tube and provides
secure clamping retention. The mounting block pivots freely in zinc right
angle brackets to allow mounting the assembly via clearance holes for 1/4"
dia. bolts.
The lock washers must be used as indicated (between the bolt head and
the top clamp piece). Assemble the top clamp piece as follows.
1. Tighten both bolts so that the top clamp half draws down evenly on
the sensor tube.
2. Tighten the bolts until both lock washers are flat.
3. Then turn each bolt an additional ½
to ¾ turn.
ORDERING INFORMATION
.88
(22.4)
2.9
(73.7)
3.4
(86.4)
2.5 (63.5)
1.25
(31.8)
.25 (6.3)
Lock washers (2) must be
installed between bolt heads
and top clamp piece.
E-clip retaining ring (2)
must be installed in slots.
5.70 (144.8)
4.50 (114.3)
(50.8)
(38.1)
0.75
0.75 (19.0)
4X Ø 0.31 (7.9)
2.00
1.50
(19.0)
SINGLE WHEEL
2.93 (74.4)
DUAL WHEEL 4 (101.6)
(21.6)
.85
SINGLE SHAFT
UNITS
THIS WHEEL
AND SHAFT
OMITTED ON
.88 (22.4)
WHEEL
RADIUS
1.9
(48.3)
6.9
(175.3)
FRONT
VIEW
TOP
VIEW
DIMENSIONS In inches (mm)
CAUTION: Downward tension
on signal cable can cause
wheel(s) to lift. Make sure
cable is clamped to
machine frame near
encoder and allow slack.
NOTE: The weight at the
Length Sensor unit
provides sufficient traction
for accurate operation
when mounted as shown,
with arm angle from
horizontal not exceeding
±30°, and with hinge clamp
toward the far extreme of
the extension arm.
Length Sensors should be mounted so measuring
wheel(s) contact ribbon, strip or web as it passes over
a roller. As an alternative, wheel(s) can be driven by
roller surface next to material being measured.
MODEL NO. DESCRIPTION PART NUMBER
LSAHC LSAHC001 Length Sensor Hinge Clamp Assembly
MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY
Note: After installation of measuring wheels, ensure guards,shields or other
devices are in place to protect personnel from rotating equipment.
WHEEL CODE CIRCUMFERENCE TOLERANCE PART NUMBER
1 foot (1/3 yd) ±0.35% WF1000OK
OK
1/3 meter ±0.30% WM0333OK
4/10ths yard ±0.30% WY0400OK
4/10ths meter ±0.30% WM0400OK
BK (Balanced) 1 foot (1/3 yd) ±0.35% WF1000BK
Replacement Tires
for OR Wheels
1 foot (1/3 yd) TORF1000
1/3 meter TORM0333
4/10ths yard TORY0400
4/10ths meter TORM0400
TOLERANCE WHEEL CODE CIRCUMFERENCE PART NUMBER
1 foot (1/3 yd) ±0.40% WF1000OR
OR
1/3 meter ±0.40% WM0333OR
4/10ths yard ±0.40% WY0400OR
4/10ths meter ±0.40% WM0400OR
1 foot (1/3 yd) ±0.35% WF1000OF
OF
1/3 meter ±0.30% WM0333OF
4/10ths yard ±0.30% WY0400OF
4/10ths meter ±0.30% WM0400OF
BF (Balanced) 1 foot (1/3 yd) ±0.40% WF1000BF
WHEELS & REPLACEMENT TIRES FOR CODE OR WHEELS
ORDERING INFORMATION
Model ZGH Shown
Model ZFH Shown
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls
China
Unit 101, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113-3688
Fax +86 21 6113-3683
Red Lion Controls
Europe
Printerweg 10
NL - 3821 AD Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Red Lion Controls
India
54, Vishvas Tenement
GST Road, New Ranip,
Ahmedabad-382480 Gujarat, India
Tel +91 987 954 0503
Fax +91 79 275 31 350