Red Lion MLPS2 - Manual

MLPS UNIT
MOUNTING CLIP
EXISTING PANEL
1.30 (33)
A
A. SEE APPROPRIATE LITERATURE
B
M3424B
OUTPUT POWER:
12VDC UNREG. @ 400mA OPERATING TEMP: 0° TO 60°C
85-250 VAC, 50/60Hz, 14VA
DC COMMON
INPUT POWER:
AC INPUT
TERMINAL
!
+12V
MLPS1
MODEL
YORK, PA. MADE IN U.S.A.
RED LION CONTROLS
2.65 (67.3)
B.
FOR UNIT DIMENSIONS
CUB5 - 2.96 (75.2)
CUB4, DT8 - 2.60 (66.0)
1.85 (47)
  PROVIDES POWER FOR THE MICRO-LINE SERIES
  MLPS1: 12 VDC OUTPUT @ 400 mA
  MLPS2: 24 VDC OUTPUT @ 200 mA
  EASILY ATTACHED TO BACK OF DT8, CUB4 AND CUB5
DESCRIPTION
The Model MLPS power supplies are designed to attach to the rear of the
Micro-Line Series. The MLPS1 provides a 12 VDC output, while the MLPS2
provides a 24 VDC output. Both supplies can be powered from an 85-250 VAC
source.
Caution: The maximum output current of the MLPS1 is 400 mA and the MLPS2
is 200 mA. Check the specifications of the specific counter(s)/indicators(s)
and sensors(s) being used to ensure that total current requirements do not
exceed the respective values of the power supplies.
SAFETY SUMMARY
All safety related regulations, local codes and instructions that appear in the
manual or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
MODEL MLPS1 and MLPS2 - MICRO-LINE POWER SUPPLIES
DIMENSIONS In inches (mm)
SPECIFICATIONS
1. POWER REQUIREMENTS: 85-250 VAC, 50/60 Hz, 14 VA.
2. POWER OUTPUT:
MLPS1: +16 VDC max @ 4 mA; 11.5 VDC min @ 400 mA
MLPS2: +26 VDC max @ 0 mA; 22 VDC min @ 200 mA
3. ENVIRONMENTAL CONDITIONS:
Operating Temperature: 0 to 60°C
Storage Temperature: -30 to 75°C
Operating and Storage Humidity: 85% max. (non-condensing) from 0°C
to 50°C.
Altitude: Up to 2000 meters
4. CERTIFICATIONS AND COMPLIANCES:
SAFETY
UL Recognized Component, File # E179259, UL61010-1, CAN/CSA-
C22.2 No. 61010-1
Recognized to U.S. and Canadian requirements under the Component
Recognition Program of Underwriters Laboratories, Inc.
Output meets Class 2 power requirements per UL 1310.
IECEE CB Scheme Test Report # E179259-V2-S1
Issued by Underwriters Laboratories, Inc.
IEC 61010-1, EN 61010-1: Safety requirements for electrical equipment
for measurement, control, and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Emissions and Immunity to EN 61326: Electrical Equipment for
Measurement, Control and Laboratory use.
Notes:
1. Criterion A: Normal operation within specified limits.
2. Criterion B: Temporary loss of performance from which the unit self-
recovers.
5. CONSTRUCTION: High impact black plastic. Mounting hardware
included. Installation Category II, Pollution Degree 2.
6. CONNECTION: Two position terminal block which accepts one 14 AWG
wire (torque terminal screws to 5 inch-lbs. [0.56 N-m]).
7. WEIGHT: 2 oz (47 g)
Bulletin No. MLPS1-D
Drawing No. LP0582
Released 03/10
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
MODEL NO. DESCRIPTION PART NUMBER
MLPS2
MLPS1
+24 VDC Micro Line/Sensor Power Supply
+12 VDC Micro Line/Sensor Power Supply
MLPS2000
MLPS1000
ORDERING INFORMATION
UL Recognized Component,
File # E179259
Class B EN 55011
Emissions:
0.5 cycle
Criterion A
3 V/rms
Criterion A EN 61000-4-6
EN 61000-4-11
RF conducted interference
Voltage dip/interruptions
1 kV L-L,
Criterion B EN 61000-4-5 Surge
1 kV signal
2 kV power
Criterion A EN 61000-4-4 Fast transients (burst)
1 kV signal
2 kV L&N-E power
10 V/m
Criterion A EN 61000-4-3 Electromagnetic RF fields
8 kV air discharge
4 kV contact discharge
Criterion A EN 61000-4-2 Electrostatic discharge
Immunity to Industrial Locations:
CAUTION: Risk of Danger.
Read complete instructions prior to
installation and operation of the unit.
CAUTION: Risk of electric shock.