Akiles ProLam Photo User Manual
Page 4
8
3) Temp ad justmen t
T here are Temp co ntrol keys on the control panel. Diff erent pouch film, different documen t,
d ifferent room Temp , should have diffe rent working Temp . If the laminated d ocument is not clea r,
i t might because the Temp is low, incre ase the Temp by 5
, then laminate it again, until a perfe ct
l aminated documen t appears. If the Tem p is too high, the l aminated documen t will be corrugatio n,
i f so, decrease the Temp until get the pe rfect laminated doc ument.
℃
℃
℃
N ote: If the best w orking Temp is n ot clear, set Tem p 80
and speed 3 first, then mak e
a djustment accord ing to the laminat ing result. Do not set the Temp more than 120
, in ca se
t he laminating film is melt.
3. COLD LAMINATING
1) P reparation
Turn on the power s witch, the display turns light.
W hen cold laminating, the suggested Te mp is below 40
, the suggested spee d is speed 1- 4.
2) P VC film
Take off a little glue side of the PVC fil m from the under cover paper.
3) C old laminating
P ut the glue side of PVC film on the fro nt of document par allel, make the glu ed end in front, pla ce
it between the two convex line on the input board. Slightly place the docum ent at the middle of
inlet, keep the docu ment in alignment with the inlet. The n the document wi ll be cold laminate d.
S teadily remove th e under cover pap er from the PVC film in opposite direction. (Shown as
F IGURE 2). Now a p erfect cold lamina ted document appe ar on the output boa rd.
The Tem p must be set to le ss than 50
.
N ote: Do not unco ver too much PVC film from the un der cover paper, or remove the PV C
f ilm from the under cover paper entir ely, this will make the PVC film use less.
℃
℃
CAUTION
WORKING
PLACE
This machine should be put at the dry and clean place, do not put it
at the damp pla ce or nea r the exit of cooling applia nces.
This machine should be put on the horizontal and firm place. In
front and rear of the machine, there should be su fficient place for
the document i n and out.
Do not put any articles o n the machine.
PO UCH FILM
Please use good quality pouch film, in order to show the lamination
effect , and avoid the entangleme nt.
The le ngth and width of the pouc h film should be 3-5mm la rger than
the document t o be laminated.
OBJECT
The la minating machin e use the hot press technology, do n ot use the
following objects in case laminating failu re or pouch film entangle.
2.T he width of docum ent is bigger tha n the distance bet ween the
two conve x lines on the input board..
3.The thickness of do cument i s bigger than 1mm.
6 .A ny ar ti c le s t ha t ha v e d rap e , br ea ka g e , d amp ne ss or
deformation before laminating.
7.Coin or any other hard articl es.
※
※
※
※
1.E asy-burnt materia l, easy-softened material.
4.S ingle side pouch film (PVC film).
5.The document printed by heat-sensitive paper, or an y articles
that can be faded o r transformed after heatin g.
mea ns excep tion while cold la minating operation.
MACHINE
OP ERATION
Do no t turn to other usages except the usage ra nge state d in this
operation manual.
Do not use the machine outside the room. Before l eaving, please cut
off the power supply if the operation is ov er.
If there are any problems on the machine, please do not u se it,send
it to th e dealer for repairing.
While operat ing the m achine, mind the children n earby, in case any sudden ness.
Do n ot suspe nd the el ectrical wire on the table or cabin et or any other p laces
that the child ren can to uch, or p lace eas y stumble persons .
Usin g the acc essory that not re commen ded or sold by th e manufa cturer, might
caus e damage on the machine.
The photo or docume nt once i s lamina ted, it w ill become perma nent and will
not b e taken a part.
Plea se do no t lamina te the co llected r are artic les, or s ome articles mig ht be
taken out in th e future.
ADVICES
3
℃
FIGURE 2
UNDER COVER PAPER
DOCUMENT
PVC FILM
PDF 文件使用 "pdfFactory Pro" 试用版本创建