Notifier NH-100 - Manual (Page 2)

Page 2 of 2 — DN-6997:D • 5/17/13
NOTIFIER® and FireWarden® are registered trademarks of Honeywell
International Inc. 
©2013. All rights reserved. Unauthorized use of this document is strictly
prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
Spefications
Size: 2.1" (5.3 cm) high; base determines diameter.
– B210LP(A): 6.1" (15.5 cm) diameter.
– B501(A): 4.1" (10.4 cm) diameter.
– B200SR(A): 6.875" (17.46 cm) diameter.
– B224RB(A): 6.2" (15.748 cm) diameter.
Shipping weight: 4.8 oz. (137 g).
Installation temperature:
– NH-100(A), NH-100R(A): –4°F to 100°F (–20°C to 38°C).
– NH-100H(A): –4°F to 150°F (–20°C to 66°C).
Humidity range: 10% to 93% relative humidity (noncon-
densing).
Voltage range: 15 to 32 VDC peak.
Standby current: 300 μA @ 24 VDC (one communication
every five seconds with LED blink enabled).
LED current: 6.5 mA @ 24 VDC.
Mounting: B210LP(A) flanged base, included. See “Product
Line Information: Intelligent Bases” if using a different base.
Fixed-temperature setpoint: 135°F (57°C) for the NH-100
and NH-100R(A)(A); 190°F (88°C) for the NH-100H(A).
Rate-of-rise detection: responds to greater than 15°F (8.3°C)
per minute.
Listings and Approvals
Listings and approvals below apply to the NH-100(A) Series
detectors. In some cases, certain modules may not be listed
by certain approval agencies, or listing may be in process.
Consult factory for latest listing status.
•
UL Listed: S747.
• ULC Listed: S747.
• CSFM: 7270-0028:0234.
• MEA: 387-02-E Vol. II.
• FM approved.
Product Line Information
NOTE: “A” suffix indicates ULC Listed model.
NH-100: Intelligent thermal sensor; 135° F (57° C); B210LP
base included.
NH-100A: Same as NH-100 but with ULC Listing; B210LPA
base included.
NH-100R: Same as NH-100 with rate-of-rise feature; B210LP
base included.
NH-100RA: Same as NH-100R but with ULC Listing; B210LPA
base included.
NH-100H: Intelligent fixed high-temperature thermal detector;
190° F (88° C); B210LP base included.
NH-100HA: Same as NH-100H but with ULC Listing; B210LPA
base included.
INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details about intelligent bases and their mounting, see
DN-60054.
B210LP (A) : Plug-in detector base (included); standard U.S.
flanged low-profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501
(A) : Standard European flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10.
B200SR
(A) : Intelligent sounder base capable of producing
sound output with ANSI Temporal 3 or continuous tone.
Replaces B501BH series bases in retrofit applications.
B224RB
(A) : Plug-in System Sensor relay base. Screw termi-
nals: up to 14 AWG (2.0 mm²). Relay type: Form-C. Rating: 2.0
A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @
30 VDC inductive.
B224BI(A): Plug-in System Sensor isolator detector base.
Maximum 25 devices between isolator bases (see DN-6994).
ACCESSORIES
F110: Retrofit flange to convert B210LP(A) to match the
B710LP(A) profile, or to convert older high-profile bases to
low-profile.
F110BP: Bulk pack of F110; package contains 15.
F210: Replacement flange for B210LP(A) base.
RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to
a U.S. single-gang electrical box. For use with B501(A) and
B210LP(A) bases only.
SMB600: Surface mounting kit
M02-04-00:Test magnet.
M02-09-00: Test magnet with telescoping handle.
XR2B: Detector removal tool. Allows installation and/or
removal of detector heads from bases in high ceiling applica-
tions.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
m) sections.
T55-127-010: Detector removal tool without pole.