Notifier BEAM1224(S) - Manual (Page 2)

Page 2 of 2 — DN-6975:B • 08/26/2009
Acclimate® Plus™ and System Sensor® are registered trademarks of
Honeywell International Inc.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
• Local alarm test switch.
• Local alarm reset switch.
• Remote test and reset switch (compatible with RTS151 and
RTS151KEY test stations).
Smoke detector spacing: On smooth ceilings, 30 – 60 feet
(9.1 to 18.3 m) between projected beams and not more than
one-half that spacing between a projected beam and a side-
wall. Other spacing may be used depending on ceiling height,
airflow characteristics, and response requirements. See NFPA
72.
ENVIRONMENTAL SPECIFICATIONS
Temperature: –22°F to 131°F (–30°C to 55°C).
Humidity: 10 – 93% RH noncondensing.
ELECTRICAL SPECIFICATIONS
Voltage: 10.2 to 32 VDC (BEAM1224); 15 to 32 VDC
(BEAM1224S).
Standby current (24 VDC): 17 mA maximum.
Alarm current (24 VDC): 38.5 mA maximum.
Alignment mode current (24 VDC): 28 mA maximum.
Test mode current (BEAM1224S only): 500 mA maximum @
peak test.
Relay contacts: 0.5 A @ 30 VDC.
Reset time: 0.3 seconds maximum.
Start-up time (after 2 min. reset): 60 seconds maximum.
Alarm verification time: 5 seconds maximum.
Remote output (alarm or trouble): Voltage: 15 to 32 VDC.
NOTE: Output voltage is the same as device input voltage.
Current: 15 mA maximum, 6 mA minimum. NOTE: Output cur-
rent is limited by 2.2K ohm resistor.
Heater kit BEAMHK: Voltage: 15 to 32 V. Current: 92 mA
maximum @ 32 V (heater only). Power consumption: nominal
1.6 W @ 24 V; maximum 3.0 W @ 32 V.
Heater kit BEAMHKR: Voltage: 15 to 32 V. Current: 450 mA
maximum @ 32 V (per reflector). Power consumption (per
reflector): nominal 7.7 W @ 24 V; maximum 15.0 W @ 32 V.
MECHANICAL SPECIFICATIONS
Shipping weight: 3.9 lbs (1.77 kg).
Wiring: Plug-in terminal blocks, 12 to 22 AWG (3.1 to 0.33
mm²).
Detector dimensions: 10.0" H x 7.5" W x 3.3" D (254 mm H x
191 mm W x 84 mm D).
Reflector dimensions for 16' to 230' (5 to 70 m) applica-
tions: 7.9" x 9.1" (200 x 230 mm).
Reflector dimensions for applications beyond 230'/70 m:
15.7" x 18.1" (400 x 460 mm).
Agency Listings and Approvals
These listings and approvals apply to the modules specified in
this document. In some cases, certain modules or applications
may not be listed by certain approval agencies, or listing may
be in process. Consult factory for latest listing status.
• UL Listed: S911
• ULC Listed: S911
• MEA Listed: 54-04-E
• Maryland State Fire Marshal: Permit # 2165
• CSFM: 7260-1653:168
• FM Approved
Product Line Information
NOTE: “A” suffix indicates ULC-listed model.
BEAM1224(A): Conventional beam smoke detector.
BEAM1224S(A): Conventional beam smoke detector with
integral sensitivity test.
BEAMLRK: Long range accessory kit (required for applica-
tions in excess of 230 ft/70 m).
BEAMMMK: Multi-mount kit (provides ceiling or wall mount
capability with increased angular adjustment).
BEAMSMK: Surface-mount kit.
6500-MMK: Heavy duty multi-mount kit for installations prone
to vibration, or where there is difficulty maintaining the set
angle. When installed with the transmitter/receiver unit,
65500-SMK is also required.
6500-SMK: Surface-mount kit for use with 6500-MMK.
RTS151(A): Remote test station. Replaces RTS451.
RTS151KEY(A): Remote test station with key lock. Replaces
RTS451KEY.
BEAMHK: Heating kit for use with the transmitter/receiver unit
of BEAM1224(S). For prevention of condensation.
BEAMHKR: Heating kit for use with the reflector of
BEAM1224(S). For prevention of condensation.