Kenwood C-616DV - Manual (Page 4)

6
C-616DV English
7
VIDEO COMPONENT VIDEO
Y Cb Cr
Connections
¤ CAUTION
Be sure to adhere to the following, or proper
ventilation will be blocked causing damage or
fi re hazard (Main unit and AC adapter).
• Do not place a cloth on the system or place it on a carpet
or cushion.
• Do not use the system in a poorly ventilated place.
• Do not place any objects impairing heat radiation onto
the top of the unit.
• Leave some space around the unit (from the largest
outside dimension including projection) equal to or
greater than, shown below.
Top panel : 50 cm
¤ CAUTION
The power in this equipment will not be completely cut off
from the wall outlet when the standby switch is turned off.
Install the equipment so that the wall outlet is easily
accessible and, in case of emergency, immediately unplug
the power plug from the wall outlet.
Mains plug is used as the disconnect device, It shall remain
readily operable and should not be obstructed during
intended use.
AM loop antenna
FM indoor antenna
iPod dock
Right speaker Left speaker
Connecting the FM antenna
1 Connect the lead to the [FM 75Ω] terminal.
2 Find the location that gives the best
reception.
3 Secure the antenna as high up as possible.
• The antenna supplied with the system is a basic antenna
for indoor use. For stable signal reception, the use of an
outdoor antenna (commercially available) is recommended.
Disconnect the indoor antenna first before connecting an
outdoor antenna.
¤ CAUTION on installing an outdoor
antenna
• Since antenna installation necessitates skill and experience,
always consult your dealer before installation. The antenna
should be placed at a distance from the power distribution
wires. Otherwise, an electric shock accident may occur if the
antenna falls down.
Connecting the AM antenna
1 Connect the AM antenna cord to the [AM] and [ HGND]
terminals.
2 Setup the antenna in the position and the direction to be
able to receive AM broadcast.
• The antenna supplied with the system is for indoor use. Place
it as far away as possible from the system, your TV set, the
speaker cords, AC adapter and the power cord, and point it in
the direction that provides the best reception.
Connecting the speakers
1 Connect the right speaker to terminal marked "R", with the
red wire to + and the black wire to –.
2 Connect the left speaker to terminal marked "L", with the red
wire to + and the black wire to –.
Insert this portion.
• For optimal sound performance, it is recommended to use
the supplied speakers.
• Do not connect more than one speaker to any one pair of +/–
speaker terminals.
¤ Caution for connection
• Do not plug the power cord into the power outlet until
all other connections are completed. Before unplugging
a connected cord or cable, be sure to switch the system
OFF and unplug the power cord from the power outlet in
advance.
Connecting the iPod adapter
• Connect an iPod adapter, which is provided with your iPod or
commercially available in iPod dealers, to the iPod dock of this
unit. Note that the iPod adapter is not provided with this unit.
• See page 9 for the supported iPod models.
1 Insert the iPod adapter into
unit.
iPod dock
iPod adapter
2 Connect your iPod.
To remove the iPod adapter
• Insert a thin object such as the tip of a flat-blade screwdriver
into the slit on the dock adapter and lift it to remove.
Connecting the HDMI terminal
1 When you use HDMI connection, you can change the
resolution (576p, 720p, 1080i, 1080p) for the HDMI output.
(See page 20)
The HDMI will be outputted at 576p resolution, even if you set
the resolution to 576i on the HDMI connection.
• When the no sound or noisy sound are outputted with HDMI
connection, set the HDMI AUDIO in DVD SETUP menu to
PCM. (See page 21)
• If there is noise or lines on the screen, please check the HDMI
cable.
• Not all HDCP-compatible DVI devices will work with this unit.
• If your HDMI TV does not support HDCP, the blue screen
appears on the screen.
• If the abnormal picture appears on the TV screen, turn off the
unit and then turn the unit on again.
To AC wall outlet
• Insert the plug firmly
all the way into the
AC wall outlet.
To TV with video input terminal
Video cord
Component Video
cord
Component Video cord
Video cord
HDMI cord
Power cord
AC adapter
Use the AC adapter (AC-18335A)
provided with this product.
Connect the audio output
of the VCR, etc. to the
[AUX IN] terminals on the
rear of the main unit.
Connect a subwoofer (SW-40HT
(separately available), etc.) to the [SUB
WOOFER PRE OUT] terminal on the
rear of the main unit.
FM
75Ω
B60-5820_08_00_C-616DV_English.indd 6-7 09/10/01 15:12