Texsport 14201 Single Mantle Propane Lantern - Manual

Thank you for buying a Texsport Authentic Adventure Gear product. We hope you
enjoy your new lantern and that it will serve you for many years to come. We
encourage you to read and understand each step of the set-up and safety opera-
tion instructions prior to working with this lantern.
FOR OUTDOOR USE ONLY
GENERAL SAFETY INFORMATION
• NEVER use in an enclosed area.
• DO NOT use lantern while sleeping.
• Always use lantern in the upright position.
• Always use handle to move lantern.
• DO NOT expose the propane cylinder to excessive heat.
• Always return handle to “down” position after lighting or moving. If han-
dle is left in the “up” position during operation it will become very hot
and should not be touched for at least 15 minutes after shut off.
• Never operate lantern with missing or damaged parts or mantles.
• Always inspect lantern, propane cylinder and connections for damage,
debris or dirt before attaching the lantern to the propane cylinder.
• If either lantern or propane cylinder is damaged, DO NOT USE.
• DO NOT USE AS A SPACE HEATER.
• Always attach/detach propane cylinder outdoors away from any open
flame or pilot lights and only when the lantern is cool.
• Do not use or operate if the lantern or propane cylinder is damaged.
• When storing or transporting lantern always disconnect the propane
cylinder and store it in a cool, well ventilated location, in an upright posi-
tion.
• Be sure connection to propane cylinder is tightly secure (hand tighten
only) prior to each use.
• Never operate the lantern near any flammable liquid or vapors. Keep all
flammable or combustible materials beyond the clearance zone as indi-
cated on the back panel of this booklet.
• Discontinue operation and close valve if:
– ambient temperature drops below -10˚ F.
– there is no fuel remaining in the propane cylinder
– combustion becomes unstable
– lighting cannot be performed quickly and easily
– you experience repeated flame outs
• Should blockage occur in the fuel jet do not attempt to clear with a metal
object. Call Texsport Customer Service at 800-231-1402 8AM – 5PM CST
Mon-Fri.
• Never leave lantern unattended when hot or in use.
• KEEP OUT OF REACH OF CHILDREN.
INSTRUCTIONS FOR USE
LANTERN ASSEMBLY – ASSEMBLE OUTDOORS
Step 1 ..Unpack lantern. Dispose of all packing
material. Carefully compare contents to
Illustration 1.
Step 2 ..Place the approved 16.4 oz/465 g dis-
posable propane cylinder approved for use
by the United States Department of Trans-
portation DOT-NRC 232/290 M1110 propane
cylinder into the plastic base. Unfold paddle
feet for additional stability. Illustration 2.
Step 3 ..Turn fuel valve to OFF position by twisting
clockwise fully. Illustration 3.
Step 4 ..Make sure valve adapter rubber seal is clean
and undamaged. Be certain the POL adapter
is undamaged and in it’s proper centered
position.
Step 5 ..Remove the protective cap from the propane
cylinder. Keep this cap for use when storing
the cylinder for future use.
Step 6 ..Carefully screw the propane cylinder onto the
lantern. DO NOT cross thread. Hand Tighten
Only – DO NOT use any tools. Illustration 4.
Test the connection for leaking gas:
Step 7 ..Apply soapy water to the connection area.
Leaking gas will produce bubbles.
Illustration 5.
Do you smell gas?
If yes, there is a leak.
Is the connection area extremely cold?
If so, there is a leak
DO NOT USE LANTERN IF IT IS LEAKING.
When you are sure there are no leaks, you may
proceed to setup/lighting your lantern.
ATTACHING AND PRIMING MANTLES
Attaching the Mantle
Step 1 ..Using the drawstring, tie the top of the new
mantle securely around the lip of the burner
tube. The flat side of the mantle should hang
next to the vertical section of the burner tube.
Illustration 6.
Step 2 ..Trim off any excess string. Illustration 7.
Step 3 ..Be careful not to damage the mantle during
installation. DO NOT operate lantern with a
hole in the mantle.
Priming the Mantle(s)
Step 1 ..Hold a flame source to the bottom of the
attached mantle. Allow the mantle to ignite
and burn evenly until only a white ash
remains. It will burn out by itself. Illustration
8.
Step 2 ..This process will reduce the mantle in size
and it will cause it to turn a gray/white
color.
Step 3 ..This process will take 2 to 3 minutes.
Step 4 ..The mantle(s) will now be very fragile. After
Priming DO NOT touch the mantle.
Step 5 ..Always have extra mantles available for
replacement. NEVER operate with defective
mantles. A mantle with a hole or other
defect can cause the lantern to overheat.
INSTALL THE GLASS GLOBE & HANDLE
Step 1 ..Place glass globe over the mantle and
burner tube.
Step 2 ..Attach the hood securely with the round nut,
being careful to align the hole in each side
of the hood with the corresponding hole on
the burner tube frame. Illustration 9.
Step 3 ..Install the bail handle – passing the ends
through the hood and burner tube frame.
LIGHTING THE LANTERN
Step 1 ..When lantern is completely assembled and
free of any gas leaks, position lantern on a
flat stable surface.
Step 2 ..Keeping your head and body well back,
insert flame source through lighting hole
near to the mantle. Open fuel valve turning
counter clockwise. The mantle will
light. Illustration 10.
Step 3 ..Adjust the brightness as desired with the fuel
valve.
Note: Please wait a few minutes before moving the lit
lantern. Move lantern using the bail handle.
TURNING OFF THE LANTERN
Step 1 ..Turn fuel valve to OFF position by turning
fully clockwise . Illustration 11.
Step 2 ..Allow lantern to completely cool (approx.15
minutes) before touching it.
2 3 4
illustration 1
illustration 2
illustration 3
illustration 4
illustration 5
illustration 6
illustration 7
illustration 10
illustration 11
illustration 9
illustration 8