Horner APG SmartStix HE559 - Manual

MAN0519-10 _______ Specifications / Installation
_________________________________________________________________________________________________________________________________________________________________________________________________________
02/24/2009 Page 1 of 3 ECN # 952
SmartStix
™
User Manual for the CsCAN
Versions (HE550 or HE559) of:
DQM601 DQM606
DQM701 DQM706
DIM610 DIM710
DIQ811 DIQ816
DQM602
Remote I/O for the
OCS/RCS Family
20 February 2009 MAN0519-10
1 Technical Support
For user manual updates and technical assistance, contact Technical Support:
North America: (317) 916-4274
or visit our website at www.heapg.com.
Europe: (+) 353-21-4321-266
or visit our website at www.horner-apg.com.
2
Installation / Safety
a. All applicable codes and standards need to be followed in the installation of this product.
b. For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG
or larger.
c. For detailed installation and programming information, refer to the Control Station
Hardware Manual.
3
Model Numbers
Model Prefix Description
HE550 CsCAN model with non-removable terminal strip
HE559 CsCAN model with removable terminal strip
Long or Short
Dimension Description
DIM610
(Short) 16 DC Inputs (24VDC, positive/negative logic)
DIM710
(Long) 32 DC Inputs (24VDC, positive/negative logic)
DQM601 / 606*
(Short)
16 DC Outputs (24VDC, negative logic, 0.5A)
(Note: If using DQM601 with a non-removable terminal strip, the
output rating is 0.1A.)
(* DQM606 uses positive logic.)
DQM701 / 706**
(Long)
32 DC Outputs (24VDC, negative logic, 0.5A)
(Note: If using DQM701 with a non-removable terminal strip, the
output rating is 0.1A.)
(** DQM706 uses positive logic.)
DQM602
(Long) 16 Relay Outputs (250VAC, 30VDC, 2.0A)
DIQ811 / 816***
(Long)
16 DC Inputs (24VDC, positive/negative logic)
16 DC Outputs (24VDC, negative logic, 0.5A)
(Note: If using DIQ811 with a non-removable terminal strip, the
output rating is 0.1A.)
(*** DIQ816 uses positive logic.)
4 Dimensions
a. Long Dimensions
SmartStix modules come in two sizes depending upon the model number. See
Section 3 to determine if a module has long or short dimensions.
b. Short Dimensions
c. Terminal Strips
5 General Specifications
General Specifications
Storage
Temperature -25 ° to 70° C Operating and
Storage Humidity 5 to 95% Non-condensing
Operating
Temperature 0 ° to 55° C
Pollution degree
2 or lower
Atmosphere
Free from
corrosive gases
and excessive
dust
Cooling method Self-cooling
Vibration
Occasional Vibration
Frequency Acceleration Amplitude Sweep
Count
10 ≤ f < 57 Hz - 0.075 mm
57 ≤ f ≤ 150 Hz 9.8 m/s 2 {1G} -
10 times in
each direction
for X,Y,Z
Continuous Vibration
Frequency Acceleration Amplitude Sweep
Count
10 ≤ f <
57 Hz - 0.035 mm
57 ≤ f ≤
150 Hz 4.9 m/s 2 {0.5G} -
10 times in
each direction
for X,Y,Z
Shocks
Maximum shock
acceleration 147 m/s 2 {15G}
Duration Time 11 ms.
Pulse Wave Half sine wave pulse (3 times in each of X, Y, Z directions)
Noise Immunity
Square wave impulse
noise AC: ± 1,500VDC
DC: ± 900VDC
Electrostatic
Discharge Voltage: 4kV (contact discharge)
Radiated
electromagnetic field
27 – 500MHz, 10V/m
Severity
level
All power
modules
Digital I/Os
(Ue ≥24V)
Digital I/Os
(Ue < 24 V)
Analog I/Os
Communication
I/Os
Fast Transient
Burst Noise
Voltage 2 kV 1 kV 0.25 kV
6 Network
Cable
For detailed wiring information, refer to the Control Station Hardware Manual. A handy
checklist is provided that covers panel box layout requirements and minimum clearances. See
Section 1 for our web address.
Pin Description
RED 1 V+
WHT 2 CAN_H
NC 3 No Connection
BLU 4 CAN_L
BLK 5 V-
7 ID Switches (Setting CsCAN Network Ids)
CsCAN Network IDs are set using the hexadecimal number system from 01 to FD. The decimal
equivalent is 1-253. Refer to Section 10, which shows the decimal equivalent of hexadecimal
numbers. Set a unique Network ID by inserting a small Phillips screwdriver into the two identical
switches. Note: The CsCAN Baud Rate for SmartStix I/O is fixed at 125KBaud
8 LEDs
a. Diagnostic LED Indicators
Diagnostic LED State Meaning
Solid Red RAM or ROM test failed
Blinking Red I/O test failed
Blinking Green Module is in power-up state
MS: (indicates fault status of
Module )
Solid Green Module is running normally
Solid Red Network Ack or Dup ID test failed
Blinking Red Network ID test failed
Blinking Green Module is in Life Expectancy default
state
NS: (indicates fault status of
Network)
Solid Green Network is running normally
b. Status LED Indicators
The Power Status LED illuminates Red when power is applied to the module. There are I/O Status
LED indicators for each of the Digital I/O points, which illuminate Red when an I/O point is ON.
9 SmartStix Modules
a. DIM610: 16 DC IN, Positive / Negative Logic
DIM610 Specifications
Number of input points 16 OFF to ON
Response 0 - 3ms. or less
Rated Input Current 7mA ON to OFF
Response 0 - 3ms. or less
ON Voltage Level 19VDC or less Common
Terminal 16 points / COM
OFF Voltage Level 6VDC or less Operating
Indicator LED turns on during
ON state of input
Input Characteristics Bidirectional
Isolation Method Photo Coupler
External
Connections Terminal block
connector (M3 x 6
screws)
Rated Voltage 11 – 25 VDC Altitude for
use Up to 2,000m
Internal power
Consumption (mA) 200mA Weight 5.6 oz. (159 g)
b. DIM710: 32VDC IN, Positive / Negative Logic
DIM710 INPUTS
Number of input
points
32 OFF to ON Response 0 - 3ms. or less
Rated Input Current 7mA ON to OFF Response 0 - 3ms. or less
ON Voltage Level 19VDC or less Common Terminal 16 points / COM
OFF Voltage Level 6VDC or less
Isolation Method Photo Coupler
Operating Indicator
LED turns on
during ON state
of input
Input
Characteristics Bidirectional External Connections
Terminal block
connector (M3 x
6 screws)
Rated Voltage 11 – 25 VDC
Internal power
Consumption (mA) 300 Weight 8.36oz. (237 g)
Cscape, SmartStix and CsCAN are trademarks of Horner APG.
This information is subject to change without notice.
Warning: Consult user
documentation. Warning: Electrical Shock
Hazard.
For Electronic Information, see
www.HornerOCS.com.
Signal Pin DIM610
NC* No Connection
(*Do not Connect)
FG Frame Ground
NC* No Connection
(*Do not Connect)
I1 Input 1
I2 Input 2
I3 Input 3
I4 Input 4
I5 Input 5
I6 Input 6
I7 Input 7
I8 Input 8
I9 Input 9
I10 Input 10
I11 Input 11
I12 Input 12
I13 Input 13
I14 Input 14
I15 Input 15
I16 Input 16
C Common
C Common
NC No Connection
I1
I3
I4
I5
I6
I9
I10
C
24VDC
I11
I12
I13
I14
I7
I8
I15
I16
I2
C
NC
FG
006DIM005-R1
NC
NC
4.55 [115.6mm]
4.21 [106.9mm]
1.97 [49.9mm]
1.62 [41.1mm]
0.18 [4.6mm]
1.87
[47.5mm]
0.31
[7.9mm]
HE559-With Removable
Strip
1.53
[38.9mm ]
0.31
[7.9mm ]
HE550- Without
Removable Terminal
Recommended Cable
Thick:
(Max Distance = 500m) Belden 3082A
Thin:
(Max Distance = 100m) Belden 3084A
Close-up of Switches
006DIM001
Use this switch to set
the Low Digit – has
an x1 multiplier. Use this switch to set the
High Digit –has an x16
multiplier.
I/O Status LEDs
Power and Diagnostic
LEDs
INPUT
S
LO (x1) HI (x16) MS NS PWR
SmartStix I/O
2 1 4 5 6 7 8 11 3 9 12 13 14 15 16 10
INPUTS
LO (x1) HI (x16) MS NS PWR
SmartStix I/O
2 1 4 5 6 7 8 11 3 9 12 13 14 15 16 10
Signal Pin DIM710
NC* No Connection
(*Do not Connect)
FG Frame Ground
NC* No Connection
(*Do not Connect)
I1 Input 1
I2 Input 2
I3 Input 3
I4 Input 4
I5 Input 5
I6 Input 6
I7 Input 7
I8 Input 8
I9 Input 9
I10 Input 10
I11 Input 11
I12 Input 12
I13 Input 13
I14 Input 14
I15 Input 15
I16 Input 16
C1 Isolated Common 1
I17 Input 17
I18 Input 18
I19 Input 19
I20 Input 20
I21 Input 21
I22 Input 22
I23 Input 23
I24 Input 24
I25 Input 25
I26 Input 26
I27 Input 27
I28 Input 28
I29 Input 29
I30 Input 30
I31 Input 31
I32 Input 32
C2 Isolated Common 2
NC No Connection
I3
I4
I5
I6
I9
I10
C1
24VDC
I11
I12
I13
I14
I7
I8
I15
I16
C2
I2
I31
NC
I29
I30
I27
I28
I25
I26
I23
I24
I21
I22
I19
I20
I17
I18
24VDC
I1
I32
FG
006DIM006-R1
NC
NC
6.95 [176.5mm]
6.61 [167.9mm]
1.62 [41.1mm]
0.18 [4.6mm]
1.97 [49.9mm]