Samlex America CFB2-400 - Manual

Owner's
Manual
Please read this
manual before
installing your
fuse block
400 Amp, Class T
Fuse Block
CFB2-400
1
4
11013-CFB2-400-1112
MAN-10006
2 YeAr limiTed wArrAnTY
The CFB2-400 manufactured by Samlex America, Inc. (the “Warrantor“) is warranted to be
free from defects in workmanship and materials under normal use and service. The war-
ranty period is 2 years for the United States and Canada, and is in effect from the date of
purchase by the user (the “Purchaser“).
Warranty outside of the United States and Canada is limited to 6 months. For a warranty
claim, the Purchaser should contact the place of purchase to obtain a Return Authoriza-
tion Number.
The defective part or unit should be returned at the Purchaser’s expense to the authorized
location. A written statement describing the nature of the defect, the date of purchase,
the place of purchase, and the Purchaser’s name, address and telephone number should
also be included.
If upon the Warrantor’s examination, the defect proves to be the result of defective mate-
rial or workmanship, the equipment will be repaired or replaced at the Warrantor’s option
without charge, and returned to the Purchaser at the Warrantor’s expense. (Contiguous
US and Canada only)
No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is
unable to remedy the defect after having a reasonable number of opportunities to do so.
Warranty service shall be performed only by the Warrantor. Any attempt to remedy the
defect by anyone other than the Warrantor shall render this warranty void. There shall
be no warranty for defects or damages caused by faulty installation or hook-up, abuse or
misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or
water immersion.
No other express warranty is hereby given and there are no warranties which extend
beyond those described herein. This warranty is expressly in lieu of any other expressed
or implied warranties, including any implied warranty of merchantability, fitness for the
ordinary purposes for which such goods are used, or fitness for a particular purpose, or
any other obligations on the part of the Warrantor or its employees and representatives.
There shall be no responsibility or liability whatsoever on the part of the Warrantor or
its employees and representatives for injury to any persons, or damage to person or
persons, or damage to property, or loss of income or profit, or any other consequential or
resulting damage which may be claimed to have been incurred through the use or sale of
the equipment, including any possible failure of malfunction of the equipment, or part
thereof. The Warrantor assumes no liability for incidental or consequential damages of
any kind.
Samlex America inc. (the “warrantor”)
www.samlexamerica.com
103 - 4268 Lozells Ave.
Burnaby, BC
Canada V5A 0C6 T: 604 525 3836
F: 604 525 5221
TF: 1 800 561 5885 e-mail: [email protected]
website: www.samlexsolar.com
INTRODUCTION
Fuse Protection in the Battery Circuit
A battery is an unlimited source of current. If there is a short circuit along the length of the
cables that connect the battery to the inverter, thousands of Amperes of current can flow
from the battery causing shorting: a section of the cable can overheat, the insulation can melt
and the cable can ultimately break. This interruption of high current can generate hazardous,
high temperature, high energy arc accompanied by a high pressure wave that may cause fire,
damage to nearby objects or injury. To prevent the occurrence of such hazards under short
circuit conditions, an appropriate fuse should be used in the battery circuit with the required
current interrupting capacity (Termed AIC – Ampere Interrupting Capacity). For this purpose,
fuses with an AIC rating of 10000 A at 14 V / 5000 A at 32 V, or higher should be used.
CONsTRUCTION
The Class T Fuse Block (Fig. 1) contains the following components:
• Class T Fuse – Fig. 2: This is rated at 125 V, 400 A. It is UL Class “T” rated and UL listed as per UL
Standard 248-15. It has AIC (Ampere Interrupting Capacity) of 20,000 A.
• Fuse Holder – Fig. 3: This consists of a fibreglass insulated base with studs / bolts (5/16” diameter,
18 Threads Per Inch) and nut (requires ½” size wrench) for holding the fuse. The two terminals for
cable entry are designed for #4/0 cable (Hole size is 0.6” / 15.5 mm). Hexagonal headed socket screws
(requires Allen Key size 5/16”) are used to clamp the cable ends.
• Snap on cover: Is made of clear polycarbonate and provides touch safety.
Fig. 1. Class “T” Fuse Assembly