Campbell Scientific CR10X Prompt Sheet - Manual

INST. 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12: 13: 14:
1 VOLT (SE) REPS RANGE† SE CHAN LOC MULT OFFSET
2 VOLT (DIFF) REPS RANGE† DIFF CHAN LOC MULT OFFSET
3 PULSE REPS CHAN/PORT CONFIG† LOC MULT OFFSET
4 EX-DEL-SE REPS RANGE† SE CHAN EX CHAN† DELAY 0.01 s EXCIT mV LOC MULT OFFSET
5 AC HALF BR REPS RANGE† SE CHAN EX CHAN† EXCIT mV LOC MULT OFFSET
6 FULL BR REPS RANGE† DIFF CHAN EX CHAN† EXCIT mV LOC MULT OFFSET
7 3W HALF BR REPS RANGE† SE CHAN EX CHAN† EXCIT mV LOC MULT OFFSET
8 EX-DEL-DIFF REPS RANGE† DIFF CHAN EX CHAN† DELAY 0.01 s EXCIT mV LOC MULT OFFSET
9 FULL BR w/M EX REPS EX RANGE† BR RANGE† DIFF CHAN EX CHAN† EXCIT mV LOC MULT OFFSET
10 BATT VOLT LOC
11 TEMP (107) REPS SE CHAN EX CHAN† LOC MULT OFFSET
12 RH (207) REPS SE CHAN EX CHAN† TEMP LOC RH LOC MULT OFFSET
13 TC TEMP (SE) REPS RANGE† CHAN/LOC† TC TYPE† REF LOC LOC MULT OFFSET
14 TC TEMP (DIFF) REPS RANGE† CHAN/LOC† TC TYPE† REF LOC LOC MULT OFFSET
15 PORT SERIAL I/O REPS CONFIG† CTS/DELAY PORT OUT LOC NO. LOC T CHAR MAX IN DELAY LOC MULT OFFSET
16 RTD TEMP REPS R/Ro LOC LOC MULT OFFSET
17 INTERNAL TEMP LOC
18 TIME OPTION† MOD/BY LOC
19 SIGNATURE LOC
20 PORT SET 8765† 4321†
21 PORT w/DURATION PORT LOC DELAY 0.01 s
22 EXCIT w/DEL EX CHAN† DEL w/ex. DEL after ex. EXCIT mV†
23 BURST MODE NO. CHAN RANGE† IN CHAN OPTION† SCAN (ms) SCANS (10 3 ) SMPLS TR LIM mV EXCIT mV LOC MULT OFFSET
24 CALIBRATION LOC†
25 READ PORTS MASK† LOC
26 TIMER LOC (0 resets timer)
27 PERIOD AVG (SE) REPS OPTION† SE CHAN NO CYC LIM 0.01 s LOC MULT OFFSET
28 VIB WIRE (SE) REPS† SE CHAN EX CHAN START F† END F† NO CYC DEL 0.01 s LOC MULT OFFSET
29 PS9104E DIFF CHAN EX CHAN LOC Enhanced Parameters (CSI parameters 4-23)†
100 TDR 1502B See manual
101 SDM-INT8 ADDR C:8765† C:4321† F:8765† F:4321† AVG OPT† LOC MULT OFFSET
102 SDM-SW8A REPS ADDR FUNCT† CHAN LOC MULT OFFSET
103 SDM-AO4 REPS ADDR LOC
104 SDM-CD16AC REPS ADDR LOC
105 SDI-12 RECORDER ADDR CMD† PORT LOC MULT OFFSET
106 SDI-12 SENSOR ADDR TIME/VAL† LOC
107 SDM CSAT3 REPS ADDR OPTION† LOC
108 SDM UDG01 ADDR TEMP LOC LOC MULT OFFSET
109 SDMX50 ADDR CHAN
110 SDM GROUP TRIGGER
113 SDM-SIO4 REPS ADDR MODE COMMAND 1 ST PAR 2 ND PAR VALUES/REP LOC MULT OFFSET
114 SET TIME OPTION† LOC
115 SDM BAUD BIT PERIOD 10 µs
117 DATALOGGER ID LOC
118 SDM CAN ADDR T.QUANTA TSEG1 TSEG2 ID 0-10 ID 11-23 ID 24-28 DATA TYPES START BIT NO. BITS NO. VALUES LOC MULT OFFSET
119 TDR100 ADDR OUTPUT† MUX/PROBE† WAVFRM AV Vp POINTS C. LENGTH W.LENGTH P.LENGTH P.OFFSET LOC MULT OFFSET
130 STATUS MONITOR OPTION† LOC
131 EXTENDED VIB WIRE REPS RANGE† SE CHAN EX CHAN START F END F SWEEP NO. STEPS D MEAS CYCLES D REPS LOC MULT OFFSET
138 CS616 WATER CONTENT REPS SE CHAN PORT† LOC MULT OFFSET
188 SDM-IO16 ADDR COMMAND 1 ST PAR† 2 ND PAR† 3 RD PAR† 4 TH PAR† C.LOC LOC MULT OFFSET
1-14 RANGE codes:
Slow (2.72 ms integration time)
Fast (250 µs integration time)
60 Hz rejection
50 Hz rejection
Full scale range
0 10 20 30 Autorange
1 11 21 31 ± 2.5 mV
2 12 22 32 ± 7.5 mV
3 13 23 33 ± 25 mV
4 14 24 34 ± 250 mV
5 15 25 35 ± 2500 mV
3 CONFIGuration codes:
To record all counts:
0 High frequency (-- 64 Hz reset)
1 Low level AC (-- 64 Hz reset)
2 Switch Closure
3 High frequency, 16-bit
4 Low level AC, 16-bit
4 Low level AC, 16-bit
Discard counts beyond execution Interval
1x (x = 0-4 from above)
Discard counts, output frequency (Hz)
2x (x = 0-4 from above)
4-10,12 EXcitation CHANnel codes:
0x Excite all reps with EX CHAN x
1x Increment EX CHAN x with each rep
11 EXcitation CHANnel codes:
0x Excite all reps with channel x
1x Increment chan x with each rep
2x Excite all reps with channel x, 60 Hz rej
3x Excite all reps with channel x, 50 Hz rej
4x Increment chan x with each rep, 60 Hz rej
5x Increment chan x with each rep, 50 Hz rej
13,14 CHANnel/LOCation:
If channel is indexed, parameter 3 becomes an input
location holding a voltage measurement.
13, 14 ThermoCouple TYPE codes:
x1 T (copper-constantan)
x2 E (chromel-constantan)
x3 K (chromel-alumel)
x4 J (iron-constantan)
x5 B (platinum-rhodium)
x6 R (platinum-rhodium)
x7 S (platinum-rhodium)
x8 N (nickel-chromium)
x = 0 Normal Measurement
x = 8 TC input from A5B40 isolation
x = 9 Output -99999 if out of common mode range
(Inst. 14 only)
15 Configuration codes:
ASCII Hex Pair Binary Logic level/Baud
00 10 20 TTL, 1200 baud
01 11 21 RS-232, 1200 baud
02 12 22 TTL, 300 baud
03 13 23 RS-232, 300 baud
18 OPTION codes:
0 seconds into minute (max 60)
1 minutes into day (max 1440)
2 hours into year (max 8784)
3 store year, day, hour, minute, second into 5 input
locations
20 8765, 4321 Each digit configures respective port
0 Set low
1 Set high
2 Toggle
3 1 ms Pulse
4 10 ms Pulse
5 100 ms Pulse
6 1 s Pulse
7 Configure as output
8 Configure as input
9 No change
22 EXcitation CHANnel/EXCITation mV:
If excitation channel is indexed, parameter 4 becomes
the input location from which to get the excitation voltage.
23 RANGE codes:
Fast (250 µs integration time)
Full scale range
13 ± 25 mV
14 ± 250 mV
15 ± 2500 mV
23 OPTION code, 4 digits:
ABCD
A
Trigger
0 Trigger on 1st analog channel
1 Digital trigger on C1
2 Same as 0, but sets C1 high during measurements
B Trigger option
0 Trigger immediately
1 Trigger if above limit (high)
2 Trigger if below limit (low)
3 Trigger on rising edge
4 Trigger on falling edge
C Destination
0 Input Storage
1 Serial port, 9600 baud
2 Serial port, 76800 baud
3 Serial port, 76800 baud to Storage Module
D Measurement
0 Differential measurement
1 Single-ended measurement
24 LOCation (start of 19 calibration values)
xxxx Calibrate only when 24 is executed
xxxx-- (key in C before entering) store results of
automatic calibration
25 MASK:
Base 2 representation of ports 8-1; 1 means read,
0 means don’t read. Entered as base 10 (0-255).
Results are stored as base 2 converted to base 10.
1 indicates high, 0 indicates low or not read.
27 OPTION codes:
Code Peak-to-Peak Volts Max. Freq.
x1 2.0 mV 8 kHz
x2 3.0 mV 20 kHz
x3 12 mV 50 kHz
x4 2.0 V 200 kHz
x = 0 Output period in microseconds
x = 1 Output frequency in kHz
28 REPS: Hit C (--) to skip repeat of excit.
START Frequency of sweep (100s of Hz)
END Frequency of sweep (100s of Hz)
29 Enhanced Parameters
These parameters are listed on the manufacturer’s calibration
sheet, where:
CSI Par. Enhanced Par.
04-23: 1-20
101 C:8765, C:4321 Each digit Configures respective channel
0 High level, rising edge
1 High level, falling edge
2 Low level ac, rising edge
3 Low level ac, falling edge
101 F:8765, F:4321 Each digit sets Function for respective channel
0 No value returned
1 Period, ms
2 Frequency, kHz
3 Time since previous channel, ms
4 Time since channel 1, ms
5 Counts on 2 since 1, interpolated
6 Low resolution frequency, kHz
7 Counts
8 Integral counts on 2 since 1
101 AVeraGing OPTion
0 Execution interval averaging
0-- Continuous averaging
xxxx Specify average interval in ms
101 AVeraGing OPTion (continued)
xxxx-- Capture all events until xxxx edges of channel 1
9999-- Test Memory
102 FUNCTion
0 Channel state
1 Duty cycle
2 Counts
3 Memory test
105 SDI-12 CoMmanD codes:
Entry Command Description
0 M Initiate measurement
0-- C Initiate concurrent measurement
1..9 M1..M9 Additional measurement commands
specified by the SDI-12 sensor
10 V Initiate verify sequence
11 I Send identification
20..29 R0..R9 Send command to sensor and retrieve data
106 TIME/VALues codes:
ttnn: tt = time (seconds)
nn = No. values
107 OPTION codes:
0 Get data and measure
1..6,10,12,15,20,30,& 60 Execution Parameter
99 Get data after a group trigger
114 OPTION codes:
0 Set time with hr, min, sec values from 3 input locations
1 Set time with day, hr, min, sec values from 4 input
locations
2 Set time with yr, day, hr, min, sec from 5 input locations
119 MUltipleXer and PROBE selection:
ABCR
A
Level 1 multiplexer channel
B Level 2 multiplexer channel
C Level 3 multiplexer channel
R Number of probes to be read, starting with the
channel specified by the ABC value
Enter 0 when level is not used.
119 OUTPUT options
0 Measure La/L
1 Collect waveform values
2 Collect waveform plus first derivative
3 Measure electrical conductivity
130 OPTION codes:
0 Watchdog errors
1 Table overruns
2 Low voltage counts
3 Lithium battery (volts)
4 Flash errors (CR10X-IM and CR10X-2M only)
10 Stores OS version, OS revision, and OS signature in three
consecutive locations
131 RANGE:
1 8 kHz @ 2 mV peak-to-peak
2 20 kHz @ 3 mV peak-to-peak
3 50 kHz @12 mV peak-to-peak
4 200 kHz @ 2 V peak-to-peak
138 PORT:
X Specifies the first control port used. Subsequent repetitions
are enabled with the next higher control port.
1X All repetitions are enabled with the specified control port.
188 1 ST PAR, 2 ND PAR, 3 RD PAR, 4 TH PAR:
1ST PAR configures ports 16-13; 2ND PAR configures ports 12-9;
3RD PAR configures ports 8-5; 4TH PAR configures ports 4-1;
each digit configures respective port
0 Ouput logic low
1 Output logic high
2 Input digital, no debounce filter
3 Input switch closure, 3.17 ms debounce filter
4 Input digital interrupt enabled, no debounce filter
5 Input switch closure, interrupt enabled, 3.17 ms debounce filter
9 No change
INST. 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12:
49 SPA MAX SWATH 1ST LOC MAX LOC†
50 SPA MIN SWATH 1ST LOC MIN LOC†
51 SPA AVG SWATH 1ST LOC AVG LOC
52 RUNNING AVG REPS SOURCE DEST # IN AVG
53 A * X+B START LOC A1 B1 A2 B2 A3 B3 A4 B4
54 BLOCK MOVE NO VALS S LOC S STEP D LOC D STEP
55 POLYNOMIAL REPS X F(X) C0 C1 C2 C3 C4 C5
56 SAT VP TEMP LOC
57 WB/DBT to VP PRESSURE DB TEMP WB TEMP LOC
58 LP FILTER REPS X F(X) WGHT F
59 RF (X/1-X) REPS X MULT (RF)
60 FFT LOG
2
(SMPL) OPTION† LOG
2
(AVG) LOC MULT
61 INDIR MOVE SOURCE X DEST Y
62 COV/CORR VALUES MEANS VAR S DEV COV CORRS SAMPLES S LOC D LOC
63 EXT PARA 2-DIGIT †(8 parameters, depends on the inst. that 63 follows)
64 PAROSCIENTIFIC VALUES LOC† DEST LOC†
65 BULK LOAD F F F F F F F F LOC
66 Z=ARCTAN(X/Y) X Y Z
67 DYNAGAGE B LOC KSH RESIST AREA CONDUCT TC GAP LF CUTOFF HF CUTOFF OUTPUT† D LOC MULT OFFSET
68 EXT PARA 4-DIGIT †(8 parameters, depends on the inst. that 68 follows)
INST. 01: 02: 03:
30 Z=F*10 EXP F EXP Z
31 Z=X X Z
32 Z=Z+1 Z
33 Z=X+Y X Y Z
34 Z=X+F X F Z
35 Z=X-Y X Y Z
36 Z=X * Y X Y Z
37 Z=X * F X F Z
38 Z=X/Y X Y Z
39 Z=SQRT(X) X Z
40 Z=LN(X) X Z
41 Z=EXP(X) X Z
42 Z=1/X X Z
43 Z=ABS(X) X Z
44 Z=FRAC(X) X Z
45 Z=INT(X) X Z
46 Z=X MOD F X F Z
47 Z=X Y X Y Z
48 Z=SIN(X) X Z
PROCESSING INSTRUCTIONS
(F is fixed value (constant); X, Y, & Z are input locations)
INST. 01: 02: 03: 04: 05: 06: 07: 08: 09: 10:
69 WIND VECTOR REPS SMPL/SUBINT† SEN/OUT† WS/E WD/N
70 SAMPLE REPS LOC
71 AVERAGE REPS LOC
72 TOTALIZE REPS LOC
73 MAXIMUM REPS TIME† LOC
74 MINIMUM REPS TIME† LOC
75 HISTOGRAM REPS BINS FORM† B SEL LOC WV LOC† LOW LIM HIGH LIM
77 REAL TIME OPTION†
78 RESOLUTION OPTION†
79 SMPL ON MAX/MIN REPS LOC (must follow Inst. 73 or 74)
80 STORE AREA AREA† LOC/ID
81 RAIN HISTOGRAM REPS S LOC SWATH MEAN BINS AMP BINS LOW LIM HIGH LIM MIN AMP OPTION† D LOC†
82 STD DEV REPS LOC
69 SaMPLes/SUBINTerval (std dev):
0 No subinterval
xxxx Number of scans per subinterval
SENsor type/OUTput codes:
x0 Avg WS, Θ1, σ(Θ1)
x1 Avg WS, Θ1
x2 Avg WS, resultant U, Θu; σ(Θu)
x = 0 (anemometers & vanes)
x = 1 (north- & east-facing propellers)
Where: Θ1 = Avg unit vector dir
σ(Θ1) = Std dev dir (Yamartino)
Θu = Avg resultant vector dir
σ(Θu) = Std dev dir (CSI)
73,74 TIME of max or min:
00 Max/min value only
01 With seconds
10 With Hour-Minute
11 With Hour-Minute, Second
75 FORM codes:
0 Open form (data beyond limits are
included)
1 Closed form (data beyond limits are
excluded)
WV LOCation:
0 Frequency Distribution
xxxx Weighted Value Loc
77 OPTION codes:
xxx1 Seconds
xx1x Hour-Minute
xx2x Hour-Minute, 2400 at midnight
x1xx Day
x2xx Day, Previous day at midnight
1xxx Year
(0 - no output, e.g., 110 = Day, Hr-Min)
78 OPTION codes:
0 Low resolution
1 High resolution
80 AREA codes:
1 Final Storage 1
2 Final Storage 2
3 Input Storage
81 OPTION:
00 Closed form/Fraction output
01 Closed form/Counts output
10 Open form/Fraction output
11 Open form/Counts output
D LOC
0 Send directly to Final Storage
xxxx First input location to store histogram
† Option Codes
Note: A Program Control instruction that sets the output flag high is
required to obtain output data from these instructions.
† Option Codes
49, 50 MAX/MIN:
0xxx
Store spatial max or min at loc xxx
1xxx Store max or min at loc xxx & loc of max or min at xxx+1
60 OPTION codes:
0x Power spectra
1x Real and imaginary
2x Magnitude and phase
x = 0 No taper
x = 1 Taper
63, 68 PARAMETERS 1-8:
Following Inst. 97 RF IDs & Phone No.: 1 digit at a time
32 Between RF IDs (e.g., repeater & site)
32 & 84 Between RF & Phone Modem No.
70 After last RF
13 To end
Following Inst. 98 (256 character limit) Base 10 value of
ASCII Character (1-99) 00 To end
64 VALUES LOC:
Start Loc: U(t), Tau, U0..T5
64 DESTination LOCation:
Start Loc: Temp (°C), pressure (psi), Signature
67 OUTPUT codes:
0 Short (sap flow, Kshapp)
1 Long (sap flow, Kshapp, dT, W, Qv, Qr, Qf)
OUTPUT PROCESSING INSTRUCTIONS
† Option Codes
INPUT/OUTPUT INSTRUCTIONS
CR10X INSTRUCTIONS AND PARAMETERS
}
Sets duration for subsequent
Pulse Port Command.