Allen & Heath RPS14 - Manual (Page 5)

RPS14 User Guide 5
Introduction
This user guide presents a quick reference to the RPS14. We recommend that you read this fully
before starting. Included is information on installing, connecting and operating the power supply
unit along with panel drawings and technical specification. Whilst we believe the information in this
guide to be reliable we do not assume responsibility for inaccuracies. We also reserve the right to
make changes in the interest of further product development.
We are able to offer further product support through our worldwide network of approved dealers
and service agents. You can also access our Web site (www.allen-heath.com) for information on
our company and its pedigree, our full product range and our design philosophy. To help us
provide the most efficient service please keep a record of your power supply unit serial number,
and date and place of purchase to be quoted in any communication regarding this product. The
serial number is located on the rear panel.
Check the Packing Contents
Retain the product packing should you need to ship the product in future. You should find the following
components:
1x RPS14 POWER SUPPLY UNIT. This is packed with its
rubber feet fitted. The feet can be removed for rack mounting.
1x IEC MAINS LEAD with moulded plug. Check that the plug is
suitable for connection to your local mains supply.
RPS14/n Unit shipped as a spare. n = mains voltage
1x SHORT (0.75m) male>male DC POWER CABLE.
Part number 002-584. Connects the RPS14 as a backup to the
main console supply.
Or:
+RPS14/n Unit shipped with console. n = mains voltage
1x LONG (2.9m) male>female DC POWER CABLE.
Part number 002-583. Connects the RPS14 to the mixing
console.
DOCUMENTATION including Safety Sheet AP3345, this user
guide AP5716 and the Registration Card AP3594.
The RPS14
The slimline RPS14 power supply unit is a high performance, low noise linear power supply producing DC
voltages by rectifying, smoothing and regulating AC voltages from the secondary windings of a mains transformer.
Allen & Heath mixing consoles employ a number of DC voltage supply levels in their operation and these are
provided at the output of the power supply unit. The RPS14 has a built in combiner for connection to a second
supply for backup. Full protection and thermal sensing fan cooling ensures the power supply unit will operate
consistently.
ALLEN&HEATH RPS14
CONSOLE PSU AUTO COMBINING LINEAR TECHNOLOGY
+/-17V +12V +48V
POWER ON
ON
OFF
HI TEMP
DC POWER OUT 1 DC POWER IN (OUT 2)
PIN 5 = D GND
PIN 7 = -17V @ 8A
PIN 6 = +48V @ 500mA
PIN 3 = CHASSIS GND
PIN 4 = A GND
PIN 2 = +17V @ 8A
PIN 1 = +12V @ 5A TO CONSOLE
MAIN
REDUNDANT
SUPPLIES
COMBINING
S/No
MADE IN ENGLAND
MAINS INPUT
V AC ~ 47- 63 Hz
525W MAX FUSE
GROUND
CHASSIS
CAUTION
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK
THIS APPARATUS MUST BE EARTHED BY THE POWER CORD.
DO NOT OBSTRUCT VENTILATION OPENINGS.
DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE.
COUPER L'ALIMENTATION AVANT DE CHANGER LE FUSIBLE.
WITH SAME TYPE AND RATING. DISCONNECT SUPPLY BEFORE CHANGING FUSE.
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE
RPS14 CONSOLE PSU ALLEN&HEATH
100-120V~
220-240V~ T8A L 250V 20mm
T10A L 250V 20mm
FUSE TYPE AC SUPPLY
HI TEMP
OFF
ON
POWER ON
+48V +12V +/-17V
AUTO COMBINING LINEAR TECHNOLOGY CONSOLE PSU
RPS14 ALLEN&HEATH