Samsung LE46B579A5S - Manual (Page 15)

English - 13
Satellite System Setup
Set the LNB used for receiving broadcasting signal.
Satellite System Setup is available when Antenna is set to Satellite.
The PIN input window appears.
Before running
Auto Store, set Satellite System Setup. Then channel scan is run
normally.
LNB Power
Enables or disables the power supply for the LNB.
Set whether TV provides power supply of LNB.
This function is for making only one TV can provide power supply when using one LNB
connecting to two TVs.
LNB Settings
Configures the outdoor equipment
Satellite: Selects the satellite for receiving digital broadcasts.
Transponder: Selects a transponder from the list or adds a new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a lower frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a higher frequency.
Tone 22 KHz: Selects the 22kHz tone depending on the LNB type. For a universal LNB it should be Auto.
Signal Quality: Display the current status of broadcasting signal.
Positioner Settings
Positioner: Enables or disables the positioner control
Positioner Type: Sets the positioner type between DiSEqC 1.2 and USALS (Universal
Satellite Automatic Location Sysem).
User Mode: Sets the position of satellite antenna according to each satellite. If you store
the current position of satellite antenna according to a certain satellite, when the signal of
that satellite is needed, the satellite antenna can be moved to pre-populated position.
Satellite: Selects the satellite to set the position for.
Transponder: Selects a transponder from the list for signal reception.
Moving Mode: Selects the movement mode between discrete and continuous
movement.
Step Size: Adjusts the step size degrees for the antenna rotation. Step Size is
available when Moving Mode is set to Step.
Go To Stored Position: Rotates the antenna to the stored satellite position.
Antenna Position: Adjusts and stores the antenna position for the selected satellite.
Store Current Position: Stores current position as the selected positioner limit.
Signal Quality: Display the current status of broadcasting signal.
Installer Mode: Set limits to the scope of movement of satellite antenna or reset the
position. Generally, installation guide uses this function.
Limit Position: Selects the direction of positioner limit.
Antenna Position: Adjusts and stores the antenna position for the selected satellite.
Store Current Position: Stores current position as the selected positioner limit.
Go To Zero: Stores current position as the selected positioner limit.
Reset Positioner Limit: Allow the antenna to rotate over the full arc.
Reset All Settings
Reloads the default transponder database.
❑
N
N
N
■
■
●
●
●
●
●
●
●
■
●
●
●
•
•
•
•
•
•
•
•
●
•
•
•
•
•
■
U Move E Enter R Return
Positioner Settings
Positioner : On ▶
Positioner Type : USALS
User Mode
Installer Mode
U Move E Enter R Return
User Mode
Satellite : Astra_19.2E ▶
Transponder : 10743 MHz, H/L
Moving Mode : Step
Step Size : 1
Go To Stored Position
Antenna Position
: West š ▶East
Store Current Position
Signal Quality 0
U Move E Enter R Return
Installer Mode
Limit Position : East ▶
Antenna Position : West š ▶East
Store Current Position
Go To Zero
Reset Positioner Limit
U Move E Enter R Return
LNB Settings
Satellite : Astra_19.2E ▶
Transponder : 10743 MHz, H/L
DiSEqC Mode : 2/4
Lower LNB Oscillators : 9750 MHz
Upper LNB Oscillators : 10600 MHz
Tone 22 KHz : Auto
Signal Quality 0
U Move E Enter R Return
Satellite System Setup
LNB Power : On ▶
LNB Settings
Positioner Settings
Reset All Settings
[570_Italy]BN68-02324K-00L04.ind13 13 2009-09-15 ¿АИД 1:34:29