AFX CYF152400L30D1SN - Manual

CYF Series
Classic Ceiling Fixture
Fluorescent Models: 11126, 11213, 11218, 15213, 15218, 15226
LED Models: 11600, 111100, 151100, 152200
Page 1 of 1 8060366 rev.0
Safety Precautions
Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.
It is recommended that all wiring be performed by a qualified
electrician. This fixture must be wired in accordance with all national
and local electrical codes.
Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet or damp surface or
in water.
Make sure that the power source conforms to the requirements of the
fixture (see labels on fixture housing).
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel. The green ground
screw location is clearly marked on the fixture housing.
This fixture is intended to be used for general indoor lighting in dry
or damp locations only.
Assembly Instructions
1. Preparing for installation
A. Disconnect electrical power before installing or servicing any part of this fixture.
B. Remove fixture from cartoning; remove frame, diffuser lens (3), round decorative
nut (1) and finial (2).
C. If not completed, install the stem (9) into bracket (8) and secure with lock washer
and hex nut (5) provided.
2. Wiring
All wiring must take place inside junction box. Caution : Make sure power is
off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power
supply wires are within three inches of ballast, use wire suitable for at least 90°C
(194°F). Note: Most dwellings built before 1985 have supply wire rated to 60°C.
Consult a qualified electrician before installing.
A. This unit will not operate properly unless connected to a “grounded” electrical
circuit. Electrical shock, over heating, low or no light output, and shortened lamp
life can result if proper grounding is not done. Securely attach green (or green and
yellow) wire to ground supply wire.
B. Using wire connectors (provided), connect white supply wire to white fixture lead. Connect black hot supply wire to black
fixture lead. Do not mix wires. Pull on each wire to make sure connections are secure. Make certain no bare wires are exposed
outside of wire connectors. Note – for models with luminaire disconnect pre-wired to ballast, reference the included
instruction insert.
3. Mounting
Note: Mount to a secure ceiling surface to fully enclose back of unit.
A. Mount the ceiling pan to the junction box (not provided) with the two #8-32 x 1-1/2 ” screws (4) provided.
4. Installing lamps (lamps included with models containing “GU27”)
A. GU24 Fixtures: Line up lamp pins with the corresponding holes in lamp socket and turn clockwise until lamp locks in place.
Repeat for each lamp.
B. CFQ Fixtures: Line up lamp pins with the corresponding holes in lamp socket and push until lamp locks in place. Repeat for
each lamp.
5. Mounting diffuser
A. Slide diffuser (3) and finial (2) over stem (9) and secure with round decorative nut (1).
6. Power to the fixture can now be restored
Limited Factory Warranty
AFX Lighting, Inc. hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a
period of 3 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover
failure due to improper installation, misuse, mishandling or damage incurred in transit.
FIG 2
CYF15126 Model Shown