AFX CEW113PNEC - Manual

CEW Series
Outdoor Fluorescent Wall Sconce
Model 113, 118
Page 1 of 1 8060156 Rev 2
Safety Precautions
Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.
It is recommended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet surface.
This fixture is designed for use in a 110-120VAC, 60Hz fused circuit.
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel.
This fixture is intended to be used for general outdoor lighting in wet
locations, mounted at least 4’ above ground level.
Assembly Instructions
1. Preparing for installation
A. Disconnect electrical power before installing or servicing any part of this
fixture.
B. Remove contents from carton. Locate the diffuser (1) and forks (2&11).
C. Remove screws and washers (4&10) from forks. Attach upper fork (2&4) and
lower fork (10&11) to diffuser (1) as shown.
2. Wiring. All wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires
for damage or scrapes, consult a qualified electrician before installing.
A. This unit will not operate properly unless connected to a “grounded” electrical
circuit. Electrical shock, over heating, low or no light output, and shortened
lamp life can result if proper grounding is not done. Securely attach green and
yellow wire from back of fixture to gem bar (6) gnd.
B. Using wire connectors (provided), connect white supply wire to white lead(s).
Connect black hot supply wire to black lead. Do not mix wires. Make sure
connections are secure and tucked carefully into junction box (not provided).
3. Fixture mounting
A. Back pan mounting options:
1. Gem Bar Mounting – Secure gem bar (provided) to junction box. Install 1-
1/2” stem (7) (provided) into the gem bar. Use the lock nut (supplied) to secure stem at the proper length. Install back pan
(8) over stem and secure in place with knob (9). (Note: Adjust length of stem to create secure fit.)
2. Secure to junction box – Holes supplied in back pan (8) enable direct mounting to junction box (not supplied).
B. Apply a bead of silicone sealant (not supplied) around all 4 edges of back pan (8) at wall following manufacturer’s instructions.
4. Lamp and Diffuser installation
A. Install appropriate lamp (4-pin 13 G24q-1 or 18 watt G24q-2 base) (not supplied) from bottom by inserting lamp pins into lamp
holder and pressing up until lamp snaps into place.
B. Place clear rubber washer (not shown) over bracket mounting hole in clear acrylic top diffuser (5).
C. Align pin and hole in upper bracket with corresponding ones in the top diffuser.
D. Mount the diffuser assembly to housing assembly (8) by placing upper fork (2) over the clear acrylic top diffuser (5) and secure
with thumbscrew (3).
E. Restore power at fuse or circuit breaker box.
NOTE: If the fixture is provided with a photocell, it is pre-wired from the factory. This unit will not operate until insufficient
ambient light allows the photocell to operate the lamp.
Limited Factory Warranty
American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components;
it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.