Allied Telesis AT-SPLX10 SFP - Manual

PN 613-50640-00 Rev. A PN 613-50640-00 Rev. A PN 613-50640-00 Rev. A PN 613-50640-00 Rev. A
AT-SPLX10 SFP Transceiver Installation Guide
Overview
The AT-SPLX10 SFP transceiver is capable of reaching a
maximum operating distance of up to 10 km and transmits
using a 1310 nm wavelength.
The AT-SPLX10 transceiver is designed to be used in ATI
products such as the AT-8000 and AT-9400 series switches.
Verifying Package Contents
Make sure that the AT-SPLX10 transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
AT-SPLX10 Specifications
The SFP transceiver uses a fiber optic cable with LC
connectors.
Laser
Class 1 laser product. Do not stare into the laser beam.
Note
A transceiver must be connected to another transceiver
or fiber optic port that has similar operating
characteristics.
Note
You can hot swap the SFP transceiver. You do not
need to power off the networking device when you
install or replace an SFP transceiver.
Installing an AT-SPLX10 SFP Transceiver
To install an AT-SPLX10 SFP transceiver, perform the
following procedure:
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
Model
Maximum
Distance
Type of Fiber Optic Cable
AT-SPLX10 10 km 9 µm single-mode fiber
AT-SPLX10 SFP Transceiver Installation Guide
Overview
The AT-SPLX10 SFP transceiver is capable of reaching a
maximum operating distance of up to 10 km and transmits
using a 1310 nm wavelength.
The AT-SPLX10 transceiver is designed to be used in ATI
products such as the AT-8000 and AT-9400 series switches.
Verifying Package Contents
Make sure that the AT-SPLX10 transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
AT-SPLX10 Specifications
The SFP transceiver uses a fiber optic cable with LC
connectors.
Laser
Class 1 laser product. Do not stare into the laser beam.
Note
A transceiver must be connected to another
transceiver or fiber optic port that has similar operating
characteristics.
Note
You can hot swap the SFP transceiver. You do not
need to power off the networking devide when you
install or replace an SFP transceiver.
Installing an AT-SPLX10 SFP Transceiver
To install an AT-SPLX10 SFP transceiver, perform the
following procedure.
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
Model
Maximum
Distance
Type of Fiber Optic Cable
AT-SPLX10 10 km 9 µm single-mode fiber
AT-SPLX10 SFP Transceiver Installation Guide
Overview
The AT-SPLX10 SFP transceiver is capable of reaching a
maximum operating distance of up to 10 km and transmits
using a 1310 nm wavelength.
The AT-SPLX10 transceiver is designed to be used in ATI
products such as the AT-8000 and AT-9400 series switches.
Verifying Package Contents
Make sure that the AT-SPLX10 transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
AT-SPLX10 Specifications
The SFP transceiver uses a fiber optic cable with LC
connectors.
Laser
Class 1 laser product. Do not stare into the laser beam.
Note
A transceiver must be connected to another
transceiver or fiber optic port that has similar operating
characteristics.
Note
You can hot swap the SFP transceiver. You do not
need to power off the networking devide when you
install or replace an SFP transceiver.
Installing an AT-SPLX10 SFP Transceiver
To install an AT-SPLX10 SFP transceiver, perform the
following procedure.
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
Model
Maximum
Distance
Type of Fiber Optic Cable
AT-SPLX10 10 km 9 µm single-mode fiber
AT-SPLX10 SFP Transceiver Installation Guide
Overview
The AT-SPLX10 SFP transceiver is capable of reaching a
maximum operating distance of up to 10 km and transmits
using a 1310 nm wavelength.
The AT-SPLX10 transceiver is designed to be used in ATI
products such as the AT-8000 and AT-9400 series switches.
Verifying Package Contents
Make sure that the AT-SPLX10 transceiver and installation
instructions are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales
representative for assistance.
AT-SPLX10 Specifications
The SFP transceiver uses a fiber optic cable with LC
connectors.
Laser
Class 1 laser product. Do not stare into the laser beam.
Note
A transceiver must be connected to another
transceiver or fiber optic port that has similar operating
characteristics.
Note
You can hot swap the SFP transceiver. You do not
need to power off the networking devide when you
install or replace an SFP transceiver.
Installing an AT-SPLX10 SFP Transceiver
To install an AT-SPLX10 SFP transceiver, perform the
following procedure.
Caution
The transceiver can be damaged by static electricity.
Be sure to observe all standard electrostatic discharge
(ESD) precautions, such as wearing an antistatic wrist
strap, to avoid damaging the device.
Model
Maximum
Distance
Type of Fiber Optic Cable
AT-SPLX10 10 km 9 µm single-mode fiber