Allied Telesis AT-G8BD-13/-14 Bidirectional GBIC - Manual

PN 613-50677-00 Rev. B PN 613-50677-00 Rev. B
AT-G8BD-13/-14 Bidirectional GBIC
Transceivers Installation Guide
Overview
The AT-G8BD Series Bidirectional GBIC transceivers
provide Gigabit Ethernet connectivity over a single fiber
optic cable for Allied Telesyn networking products.
Both models feature a single SC connector.
Note
A transceiver must be connected to another
transceiver or fiber optic port that has compatible
operating characteristics. For instance, the
AT-G8BD-13 transceiver must be connected to an
AT-G8BD-14 transceiver or another optical interface
with operating characteristics compatible with the
AT-G8BD series transceivers.
Laser
Class 1 laser product.
Laser
Do not stare into the laser beam.
Model
Type of Fiber
Optic Cable
TX RX
AT-G8BD-13 9 micron SMF 1310 nm 1490 nm
AT-G8BD-14 9 micron SMF 1490 nm 1310 nm
444
Electrical Safety, and Emission Statements
This product meets the following standards.
RFI Emissions FCC Class A, EN55022 Class A, VCCI
Class A
Warning: In a domestic environment this product may
cause radio interference in which case the user may be
required to take adequate measures.
Immunity EN 55022
Electrical Safety UL 1950 (
C
UL
US
), EN 60950 (TUV),
EN60825, CSA C22.2-No.950-95
U.S. Pat. No. 6,939,058
Copyright © 2005 Allied Telesyn, Inc. All rights reserved. No
part of this publication may be reproduced without prior
written permission from Allied Telesyn, Inc.
www.alliedtelesyn.com
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
AT-G8BD-13/-14 Bidirectional GBIC
Transceivers Installation Guide
Overview
The AT-G8BD Series Bidirectional GBIC transceivers
provide Gigabit Ethernet connectivity over a single fiber
optic cable for Allied Telesyn networking products.
Both models feature a single SC connector.
Note
A transceiver must be connected to another
transceiver or fiber optic port that has compatible
operating characteristics. For instance, the
AT-G8BD-13 transceiver must be connected to an
AT-G8BD-14 transceiver or another optical interface
with operating characteristics compatible with the
AT-G8BD series transceivers.
Laser
Class 1 laser product.
Laser
Do not stare into the laser beam.
Model
Type of Fiber
Optic Cable
TX RX
AT-G8BD-13 9 micron SMF 1310 nm 1490 nm
AT-G8BD-14 9 micron SMF 1490 nm 1310 nm
444
Electrical Safety, and Emission Statements
This product meets the following standards.
RFI Emissions FCC Class A, EN55022 Class A, VCCI
Class A
Warning: In a domestic environment this product may
cause radio interference in which case the user may be
required to take adequate measures.
Immunity EN 55022
Electrical Safety UL 1950 (
C
UL
US
), EN 60950 (TUV),
EN60825, CSA C22.2-No.950-95
U.S. Pat. No. 6,939,058
Copyright © 2005 Allied Telesyn, Inc. All rights reserved. No
part of this publication may be reproduced without prior
written permission from Allied Telesyn, Inc.
www.alliedtelesyn.com
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.