Allied Telesis AT-PWR15 - Manual

Overview
The AT-PWR15, shown in Figure 1, is an DC redundant power supply (RPS)
used with the AT-CV5000 DC chassis only. When installed, the module
operates in a standby mode. If the standard power supply fails or loses power,
the AT-PWR15 module changes from standby to active and provides all
power to the system to prevent a network failure.
Figure 1. AT-PWR15 Power Supply Module
Note
The power supply is hot-swappable. You can install it without powering
OFF the AT-CV5000 chassis.
Warning
This unit may have more than one input. To reduce the risk of electric
shock, disconnect all power inputs prior to servicing the unit.
POWER
FAULT
AT-PWR1
5
215
Related Documents
This installation guide is an abbreviated version of the installation procedure.
For details on the components, features, and functions of this product, refer to
the following documents on our web site, www.alliedtelesyn.com:
❑ AT-CV5000 Media Converter Chassis Installation Guide
(PN 613-50580-00)
❑ AT-S70 Management Software User’s Guide (PN 613-50617-00)
Package Contents
Make sure the following items are included in the shipping package. If any
item is missing or damaged, contact your Allied Telesyn sales representative
for assistance.
❑ One AT-PWR15 Redundant Power Supply (DC)
❑ This Installation Guide
❑ Warranty Card
Locations of the Power Supply Slots
Figure 2 illustrates the locations of the two power supply modules at the rear
of an AT-CV5000 DC model chassis.
Figure 2. Locations of the Power Supply Slots on the Rear Panel of
an AT-CV5000 DC Model Chassis
Before installing a power supply, please note the following guidelines:
Note
The AT-CV5000 chassis comes with two slots designated for the power
supplies; however, it is shipped with one standard power supply
preinstalled and one empty slot for an optional power supply. The
redundant power supply can be ordered separately from your ATI sales
representative.
Warning
Make sure that both power supplies (primary and redundant) are rated
for the same power ratings; otherwise, the power supplies may get
damaged.
Note
For centralized DC power connection, install only in a restricted access
location.
POWER
FAULT
AT-PWR15
A B
AT-CVFAN
A
AT-CVFAN
B
40-60VDC
WARNING This unit might have more than one power input. To
reduce the risk of electric shock, disconnect all power
inputs before servicing unit. FOR CENTRALIZED DC POWER
CONNECTION, INSTALL ONLY IN
A RESTRICTED AREA.
40-60VDC
WARNING This unit might have more than one power input. To
reduce the risk of electric shock, disconnect all power
inputs before servicing unit. FOR CENTRALIZED DC POWER
CONNECTION, INSTALL ONLY IN
A RESTRICTED AREA.
221
PS SLOT B - Redundant PS SLOT A - Primary
Installing the AT-PWR15 Power Supply
To install the AT-PWR15, perform the following procedure:
1. Unpack the new AT-PWR15 module from its shipping container and store
the package material in a safe location.
Note
You must use the original shipping material if you need to return the
power supply module to Allied Telesyn.
2. Select the power supply slot in the AT-CV5000 chassis where you want to
install the AT-PWR15 power supply.
3. Loosen the two captive screws that secure the blank slot cover
(AT-CV5PNL2) of the selected power supply slot, and remove the blank
slot cover, as shown in Figure 3.
Figure 3. Removing the Power Supply Slot Cover
4. Slide the AT-PWR15 module into the RPS slot, as shown in Figure 4.
Figure 4. Inserting the AT-PWR15 Module into the Power Supply Slot
5. Secure the AT-PWR15 module to the AT-CV5000 chassis by using a
Phillips screwdriver to tighten the captive screws, as shown in Figure 5.
Figure 5. Securing the AT-PWR15 Module
B
100-2 40VA C ~
A T -CV5F
AN
WAR NING This u nit mig ht have more th an one power input. T o
reduce the ris k of ele ctric s hock, d isconn ect all p ower FOR C ENTR ALIZE D DC POW ER
CONN ECTIO N, INS TALL ONLY IN
A RE STRIC TED A REA. B
218
B
A T -CV5F
AN
B
WAR NING This u nit m ight ha ve mor e than o ne pow er in put. To
reduce the ris k of e lectric shock , disco nnect al l powe r FOR C ENTR ALIZE D DC POW ER
CONN ECTIO N, INS TALL ONLY IN
A RE STRIC TED A REA.
POWER
FAULT
AT-PW
R15
216
B
A T -CV5F
AN
B
POWER
FAULT
AT-PWR15
WAR NING This unit might ha
ve more tha n one po wer input. To
reduce the risk of elec
tric shoc k, disconnect all po
wer FOR CE NTR ALIZE D DC P OWER
CONN ECT ION, IN STAL L ON LY IN
A RE STRIC TED A REA.
220
CONVERTEON™ Family
AT-PWR15 Redundant Power Supply (DC)
Installation Guide
Allied Telesyn, Inc.
www.alliedtelesyn.com
PN 613-50586-00 Rev A 1 2 3