Allied Telesis AT-PB300 Series - Manual

Technical Specifications
Maximum Operating Temperature: 0° C to 40° C (32° F to 104° F)
Maximum Storage Temperature: -20° C to 80° C (-4° F to 176° F)
Operating Altitude: Up to 3,048 meters (10,000 feet)
Humidity: 5% to 80% (non-condensing)
EMC: FCC Class A, EN55022 Class A,
EN55024
Safety: EN60825, EN60950, UL1950 (UL/cUL)
Electrical Safety and Emission Statement
Standards: This product meets the following standards.
RFI Emission EN55022 Class A
WARNING: In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
Immunity EN55024
Electrical Safety EN60950, UL1950 (UL/cUL)
Laser EN60825
Copyright  2001 Allied Telesyn International, Corp.
All rights reserved. No part of this publication may be reproduced without prior written permission
from Allied Telesyn International, Corp.
Allied Telesyn International Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100
Visit our web site at: www.alliedtelesyn.co e
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to
operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Overview
The AT-PB300 Series Media Converters are hot swappable modules for the
PowerBlade Chassis. The AT-PB300 Series Media Converters are designed to
extend the distance of your network by allowing you to interconnect twisted
pair cabling and fiber optic cabling. Each unit features an 100Base-TX twisted
pair port and an 100Base-FX fiber optic port. The twisted pair port has an
RJ-45 connector and a maximum operating distance of 100 meters (328 feet).
The fiber optic port has an VF-45, MT-RJ, LC, or FJ connector, depending on
the model, and a maximum operating range of 2 kilometers (1.2 miles). The
AT-PB300 Series Media Converters operate at 100 Mbps and feature half- and
full-duplex operation.
Related Documents
This quick install guide is an abbreviated version of the installation
procedures. For complete details on the features and functions of these media
converters and for additional installation instructions, refer to the PowerBlade
Chassis Installation Guide. This guide is available from the Allied Telesyn
web site at www.alliedtelesyn.com.
Cable Specifications
The following table lists the maximum operating distances for the AT-PB300
Series Media Converters.
Model
100Base-TX 100Base-FX Port
Connector Maximum Distance Connector Maximum Distance
AT-PB301 RJ-45 100 m (328 ft) VF-45 2 km (1.2 mi)
AT-PB302 RJ-45 100 m (328 ft) MT-RJ 2 km (1.2 mi)
4 PN 613-50198-00 Rev A 010329
AT-PB300 Series
Fast Ethernet Media Converters
Quick Install Guide
For use in the PowerBlade Chassis