American Standard Ceratherm T203.740 - Manual (Page 9)

TOP
TOP
3/4" CENTRAL THERMOSTAT
WITH VOLUME CONTROL
3/4" CENTRAL THERMOSTAT
WITH VOLUME CONTROL
Installation
Instructions
M 9 6 8 4 8 0
R540
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
TEMPERATURE ADJUSTMENT
2
ROUGHING-IN DIMENSIONS
CONNECTIONS ARE: 3/4" NPT
5-7/8
II
II
3-15/16
7
3-5/8
3/4" NPT
TUB
3/4" NPT
INLET
3/4" NPT
INLET
WARNING
Prepare water supplies per ROUGHING-IN DIMENSIONS. Make sure the finished wall is between
the minimum and maximum rough dimension.
1
ROUGHING-IN THE VALVE
Install VALVE at indicated height and depth. Make sure the "TOP" marking on the PLASTER
GUARD is up.
Connect the hot and cold water supplies. Assemble all connecting pipes. Flush lines to
remove any dirt. Connections are 3/4" NPT.
Assemble the connection pipe to one of the MIXED OUTLETS of the VALVE.
Cap the other MIXED OUTLET. (Tub port is fitted with a plug at the factory).
IMPORTANT! INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES
INTO THE PIPING SYSTEM.
DO NOT SOLDER DIRECTLY TO THE VALVE BODY; THIS WILL DAMAGE
THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES.
Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD.
Check that arrow marking B points vertically upwards. If not, push the BLACK
CLAMP on the SECURING RING to the right, pull off KNOB MOUNT and reinstall
KNOB MOUNT with arrow "B" pointing upwards.
For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT until the spout
temperature is 100 F. Check that arrow marking A on the KNOB MOUNT still points
upward after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE.
Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve.
Reinstall the KNOB MOUNT so that the arrow marking A points upwards.
The maximum mixed water temperature is set at 109 F at the factory.
This setting can be changed if desired.
Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it
at the desired notch as indicated in the diagram to limit the maximum mixed water
temperature to 104 F or 112 F.
Reinstall RED LOCKING DEVICE.
KNOB
MOUNT
ARROW
"A"
BLACK
CLAMP ARROW
"B"
RED LOCKING
DEVICE
SECURING
RING
104
109
112
TEMPERATURE
LIMIT STOP
MODEL NUMBER
M 9 6 8 4 8 0 M 9 6 8 4 8 0
R540
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
923348-0070A
HANDLE ADAPTER
A994352-0070A
CARTRIDGE
954040-0070A
THERMOSTAT
CARTRIDGE
912647-0070A
O-RING
953963-0070A
HANDLE EXTENSION
953957-0070A
TEMPERATURE
CALIBRATION UNIT
A953971-0070A
CHECK STOP (COLD BLUE)
A953972-0070A
CHECK STOP (HOT RED)
TOP
CHECK STOP
(HOT RED)
PLUG
TUB
PORT
CHECK STOP
(COLD BLUE)
COLD
HOT
3
2
4
WOOD
BRACE
5
6
If the CHECK STOPS (4, 5) were removed during installation,
ensure the hot and cold CHECK STOPS (4, 5) are not reversed. The
hot CHECK STOP (4) has a red top and the cold CHECK STOP (5)
has a blue top.
CHECK STOPS (4,5) are supplied in the open position.
Closing using 5/32" (4 mm) hex wrench to pressure
test and to check for leaks.
Reassemble PLASTER GUARD (2) and FINISH
WALL.
Beware of Freezing. No water should remain
in the MIXING VALVE if freezing is a possibility.
Remove the CHECK STOPS (4,5) to completely
drain the MIXER UNIT (1).
Remove PLASTER GUARD (2) if still installed.
Turn on water supplies and check for leaks.
To flush lines, remove the CHECK STOPS (4,5)
and run water. If desired, the TEMPERATURE
CONTROL UNIT can be removed. Reinstall CHECK
STOPS (4,5) and CONTROL UNIT (6), if it was
removed.
MIXED
PLUG TUB
PORT
COLD
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
TRANSPOSED SUPPLY PIPING
OR BACK TO BACK INSTALLATION
3
Remove check stops and re-install them transposed.
Shut off water supply.
Remove handle and rim
CHECK STOP
(RED TO BLUE)
Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE
CHECK STOP is now on the left.
Turn the water supply back on and perform the temperature adjustment in step 2.
CHECK STOP
(BLUE TO RED)
918428-0070A
CARTRIDGE SCREW
3/4" NPT
SHOWER
IMPORTANT: WHEN NOT USING A
DIVERTER SPOUT A SEPARATE
DIVERTER VALVE MUST BE USED.
9 6 3 4 3 4 - Y Y Y 0 A D E E P R O U G H K I T
( S O L D S E PA R AT E LY )
NOTE: MINIMUM FLOWING PRESSURE REQUIRED FOR
THIS SYSTEM OPERATING WITH ONE SHOWER HEAD
AND 2 BODY SPRAYS IS 40 PSI
TUB PORT MUST
BE PLUGGED
HOT
3/4" 3/4"
COLD
TUB PORT MUST
BE PLUGGED
HOT
3/4" 3/4"
COLD
THERMOSTATIC BATH/
SHOWER INSTALLATION
USING A TWIN ELL, DIVERTER
SPOUT AND FIXED SHOWER
THERMOSTATIC SHOWER INSTALLATION
USING A DIVERTER VALVE, FIXED
SHOWER HEAD AND ADJUSTABLE HAND
HELD SHOWER
THERMOSTATIC SHOWER INSTALLATION USING A
DIVERTER VALVE, FIXED SHOWER HEAD, ADJUSTABLE
HAND HELD SHOWER, ON/OFF VALVE AND TWO
BODY SPRAYS
TWIN
ELL
TOP OF TUB RIM
BOTTOM OF TUB
TUB PORT
MUST BE
PLUGGED
DIVERTER
VALVE
DIVERTER
VALVE
ON/OFF
VALVE
C/L
4"
18"
(OPTIONAL)
80"-86"
912647-0070A
O-RING
6-1/4
1-5/8 - 2-1/2
HOT
1