Andis Company BGC - Manual

CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be
sure to try more than one blade, since the blade
currently being used may be dull), it could be that
your blade drive assembly needs replacement.
To change the blade drive assembly:
1. Remove blade set (Diagram G).
2. Remove drive cap (Diagram H).
3. Remove blade drive mounting screws
(Diagram I).
4. NOTE: Before removing blade drive assembly,
note the way it is positioned (this will help you in
reassembly). Remove blade drive assembly
(Diagram J).
5. Drive bearing should be at its lowest position, if
not, move it with your finger to lowest position
(Diagrams K & L).
6. Put on new drive assembly, align screw holes
and press down (Diagram J).
7. Reassemble blade drive by mounting screws
(Diagram I).
8. Replace drive cap (Diagram H).
9. Replace blade (Diagram M).
Andis ® Model BG
Detachable Blades
are compatible with Oster
®
Models 76, 10 & 111
Congratulations –
You just went First Class
when you bought this Andis Clipper.
Careful workmanship and quality design
have been the hallmarks of Andis products
since 1922.
BLADE
DRIVE
MOUNTING
SCREWS
CORRECT
POSITION
OF
DRIVE
BEARING
INCORRECT
POSITION
OF DRIVE
BEARING
DIAGRAM H
FACTORY REPAIR SERVICE
When the blades of your Andis Clipper become dull
after repeated use, it is advised to send your blades
to an Andis Authorized Service Station mentioned
above for resharpening. If you wish your clipper to be
serviced as well, they should be carefully packed
and mailed either Parcel Post Insured, or U.P.S.
LIMITED WARRANTY
This Andis product is warranted against defective material or workmanship for one year from the
date of purchase. All implied warranties arising and by virtue of State law shall also be limited to
one year. Any Andis product determined to be defective in material or workmanship during the
warranty period will be repaired or replaced without cost to consumer for parts and labor. The
defective product must be returned with proof of purchase and $6.50 to cover cost of handling,
to any Authorized Andis Repair Station or to: Andis, 1800 Renaissance Blvd., Sturtevant, WI 53177
U.S.A. or IN CANADA to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse, Lachine,
Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the nature of the problem. Due
to foreign matter sometimes found in hair, clipper blades or resharpening of blades are not sub-
ject to the one year warranty. The blade set has a 10 Day Limited Warranty. If the blade set fails
to cut, it will be resharpened free of charge if returned within 10 days of purchase. Send your
blade set postage prepaid with the original purchase receipt to: ANDIS COMPANY, ATTENTION:
Service Department, 1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A. (U.S. & Canada only).
Andis will not be liable under this warranty for any defect, failure or malfunction of any of its
products cause by normal wear, abuse, misuse, unauthorized adjustments or disassembling.
Andis will not be liable for any consequential damages resulting from any defect in material or
workmanship of any of its products. Some States do not allow limitations on how long an
implied warranty lasts or exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. The Warranty gives you specific legal
rights, and you may also have other rights which may vary from State to State.
Date
Purchased______________________________________
Model____________________________
ANDIS AUTHORIZED
REPAIR
SERVICE STATIONS
Please refer to the service stations listing
on web site for most up-to-date
Listings !
Thanks
KEEP THIS FOR YOUR RECORDS
Form # 22311 Rev. A ©2001 Andis Company, USA Printed in U.S.A.
MODEL BGC
Clipper
DIAGRAM G DIAGRAM H
DIAGRAM H DIAGRAM M
DIAGRAM I
DIAGRAM K DIAGRAM L
DIAGRAM J