ROTHENBERGER Befestigungs-Set Beton - Manual

Assembly instruction for fastening set art. no.: FF35120 concrete
1 2 3
- drilling hole
- Carefully clean the drill dust from the
borehole - Mount dowel pin by using diamond knurl threaded bar
- expansion on anker with setting tool - Turn the diamond knurl threaded bar into the dowel
- attach mounting plate of drill rig
- Enclose washer and screw on with wing nut
Only use suitable setting tool! Before using the setting tool, check by visual inspection! If any damage on setting tool, replace with new one!
Every time before start of operation make sure that the machine is firmly fastened and not able to shake!
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [email protected] · www.rothenberger.com
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ø15mm
65mm
06.10/F&E
Assembly instruction for fastening set art. no.: FF35120 concrete
Assembly instruction for fastening set art. no.: FF35120 concrete
Assembly instruction for fastening set art. no.: FF35120 concrete
1
1
1
2
2
2
3
3
3
- drilling hole
- Carefully clean the drill dust from the
borehole
- drilling hole
- Carefully clean the drill dust from the
borehole
- drilling hole
- Carefully clean the drill dust from the
borehole
- Mount dowel pin by using diamond knurl threaded bar
- expansion on anker with setting tool
- Mount dowel pin by using diamond knurl threaded bar
- expansion on anker with setting tool
- Mount dowel pin by using diamond knurl threaded bar
- expansion on anker with setting tool
- Turn the diamond knurl threaded bar into the dowel
- attach mounting plate of drill rig
- Enclose washer and screw on with wing nut
- Turn the diamond knurl threaded bar into the dowel
- attach mounting plate of drill rig
- Enclose washer and screw on with wing nut
- Turn the diamond knurl threaded bar into the dowel
- attach mounting plate of drill rig
- Enclose washer and screw on with wing nut
Only use suitable setting tool! Before using the setting tool, check by visual inspection! If any damage on setting tool, replace with new one!
Every time before start of operation make sure that the machine is firmly fastened and not able to shake!
Only use suitable setting tool! Before using the setting tool, check by visual inspection! If any damage on setting tool, replace with new one!
Every time before start of operation make sure that the machine is firmly fastened and not able to shake!
Only use suitable setting tool! Before using the setting tool, check by visual inspection! If any damage on setting tool, replace with new one!
Every time before start of operation make sure that the machine is firmly fastened and not able to shake!
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [email protected] · www.rothenberger.com
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [email protected] · www.rothenberger.com
Tel. + 49 (0) 61 95 / 800 - 1 · Fax + 49 (0) 61 95 / 7 44 22 · [email protected] · www.rothenberger.com
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ROTHENBERGER Werkzeuge GmbH · Industriestraße 7 · D-65779 Kelkheim/Germany
ø15mm
ø15mm
ø15mm
65mm
65mm
65mm
06.10/F&E
06.10/F&E
06.10/F&E