HID Magnetic Stripe Reader 740 Installation Guide User Manual

Specifications, Regulatory, Returned materials

Advertising

Specifications

INPUT:

INPUT:
Magnetic Stripe Cards, high or low coercivity, EMPI I,
EMPI II or ANSI format, up to 14 characters.

Magnetic Stripe Cards, high or low coercivity, EMPI I,
EMPI II or ANSI format, up to 14 characters.

CARD SIZE:

CARD SIZE:
CR-80, 2.125" x 3.375" x .030", Track 1, 2

CR-80, 2.125" x 3.375" x .030", Track 1, 2

OUTPUT:

OUTPUT:
Standard Wiegand 5-wire format with optional second
LED control line. Optional clock-and-data format.

Standard Wiegand 5-wire format with optional second
LED control line. Optional clock-and-data format.

DISTANCE:

DISTANCE:
200 feet with #22 AWG wire

200 feet with #22 AWG wire
500 feet with #18 AWG wire

500 feet with #18 AWG wire

TEMPERATURE RANGE:

TEMPERATURE RANGE:
-35 to +66° C (-31 to 150° F)

-35 to +66° C (-31 to 150° F)

POWER:

POWER:
12 VDC, 0.25W

12 VDC, 0.25W

READ SPEED:

READ SPEED:
5 to 50 IPS on withdrawal

5 to 50 IPS on withdrawal

DIMENSIONS:

DIMENSIONS:
6.75" H x 5.25" W x 2.75" D

6.75" H x 5.25" W x 2.75" D

LED:

LED:
Two Colors - red and green; optional amber

Two Colors - red and green; optional amber

Regulatory

FCC

FCC
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.

Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.

UL

UL
This Proximity Reader is intended to be powered from a limited
power source output of a previously certified power supply.
This Reader is intended to be used with UL 294 Listed Control
Equipment.

This Proximity Reader is intended to be powered from a limited
power source output of a previously certified power supply.
This Reader is intended to be used with UL 294 Listed Control
Equipment.

CE Marking

CE Marking
HID Global hereby declares that this proximity reader is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.

HID Global hereby declares that this proximity reader is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.

Returned Materials

Before returning any product, call Customer Service to obtain a
Return Material Authorization (RMA) number. Equipment that
fails during normal use with the warranty period (see Warranty
Information) will be repaired or replaced at the discretion of
HID Global.

Equipment that fails after the warranty period has expired from
external soures (such as lightning or abuse) will be repaired at
HID Global’s current labor rate after a repair estimate has been
provided. Following agreement by the client as evidence by a
Purchase Order or Credit Card submitted.

Warranty Information

HID Global warrants to the original purchaser that card readers
will be free from defects in material and workmanship under
normal use for two years from the date of manufacture.Unless
otherwise agreed in writing by HID Global, the buyer shall be
responsible to assure that the proper installation environment is
provided, HID Global assumes no responsibility for malfunctions
due to improper installation of products.

HID Global’s obligation under this warranty shall be limited to
the repair or replacement of any returned product, provided that
the claim is presented within two years from the date code
marked on the product.This warranty is lieu of all other
warranties of merchantability or fitness for any particular use. In
no event shall HID Global be liable for any breach of warranty in
an amount exceeding the net selling price of any defective
product.

HID Global’s obligation under this warranty shall be limited to
the repair or replacement of any returned product, provided that
the claim is presented within two years from the date code
marked on the product.This warranty is lieu of all other
warranties of merchantability or fitness for any particular use. In
no event shall HID Global be liable for any breach of warranty in
an amount exceeding the net selling price of any defective
product.

P/N 2280-3865, Rev B

July 2, 2007

P/N 2280-3865, Rev B

July 2, 2007

Parts List

Card Reader kit consists of:

Card Reader kit consists of:
1-Reader assemly

1-Reader assemly
1-Installation Kit 2270-0780

1-Installation Kit 2270-0780

• 6 Wire Cable Connector assembly

• Four 6-32 x 7/8" machine screws

• Four #6 standard washers

• Tamper switch assembly

1-Instructions NA 3865

General

Model 740 is a ruggedized pass-through card reader for
magnetic stripe access cards. The Reader is 12-Volt powered
and fully weatherproof. The reader accepts both EMPI and
ABA format cards and reports in a variety of output formats.
Three LEDs prompt the user for appropriate action.

The reader part number used when ordering is 3110-7401, or
3110-7402. Available in Black only .

Mounting

The card reader mounts on a single or double-gang electrical
'handy box' with conventional #6-32 machine screws. The
vertical spacing of the mounting screws is 3.25" and for a
double-gang handy box the horizontal spacing is 1.8125".

The reader is secured to its mounting plate with 2 tamper-proof
screws, the supplied screws are #8-32 x 0.675" oval head
screws. The driver is a #8 AVSAFE driver, HID Global
PN# 1180-0040 and is manufactured by;

The reader is secured to its mounting plate with 2 tamper-proof
screws, the supplied screws are #8-32 x 0.675" oval head
screws. The driver is a #8 AVSAFE driver, HID Global
PN# 1180-0040 and is manufactured by;

AVDEL

Corporation

AVDEL

Corporation

50 Lackawanna Avenue

Parsippany, NJ 07054

(201)

263-8100

(201)

263-8100

AVDEL PN# ASMD-0080-7750

If our choice of tamper screws is inconvenient, they may be
replaced by another brand or by #8 round head machine
screws.

9292 Jeronimo Road

Irvine, CA 92618-1905

Voice: (800) 237-7769

Fax: (949) 598-1619

email:

[email protected]

internet:

www.HIDcorp.com

Setup

WARNING
To prevent damage to equipment, make all
connections with the power "OFF" and the
connector unplugged from the reader.

Model 740 comes assembled from the factory. Located in the
box with the reader you will find the pig-tail connector which is
used to connect the reader to the external wiring.

The reader assembly is designed to be mounted vertically with
the tamper resistant oval head screws facing the floor.
Typically, the recommended reader height from the floor to the
bottom of the reader assembly is 55 inches, however, user
convenience is the determination factor.

The Lexan card slot which is part of the reader assembly is
reversible to allow the card slot angle to match the natural angle
of the wrist when holding the card during pass-through reading.
As an example, if the reader assembly is mounted on the right
side of a door, the card slot angle should point right or away
from the door. If mounted on the left side, the slot points left.

To change the card slot angle, remove the four screws holding
the back plate to the reader assembly and remove the back
plate. Remove the two screws holding the lexan card slot to the
reader assembly and carefully remove the slot so as not to
damage the connected read head wires. Rotate the card slot
and plastic shield 180

° and reassemble.

3110-7401 Model 740 Ruggedized P/T

Reader

3110-7402 Model 740 Ruggedized P/T

Reader w/ Heater Bar

Installation Guide

Advertising

Popular Brands

Popular manuals