AllTrade COMPONENT #690551-1HR - Manual (Page 17)

S SY YM MB BO OL LS S
IIM MP PO OR RT TA AN NT T:: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
S SY YM MB BO OL L N NA AM ME E E EX XP PL LA AN NA AT TIIO ON N
V Volts Voltage (Potential)
A Amperes Current
Hz Hertz Frequency (Cycles per Second)
W Watt Power
Kg Kilograms Weight
Alternating Current Type of Current
Direct Current Type of Current
Alternating or Direct Current Type of Current
Earthing Terminal Grounding Terminal
Class II Construction Denotes Double Insulation
S SY YM MB BO OL L N NA AM ME E E EX XP PL LA AN NA AT TIIO ON N
min Minutes Time
s Seconds Time
␾ Diameter Size of Drill Bits,
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
W Wh heen n u ussiin ng g tth hee C Co orrd dlleessss R Reecciip prro occaattiin ng g S Saaw w,, aallw waayyss m maaiin nttaaiin n aa ffiirrm m g grriip p o on n
tth hee tto oo oll w wiitth h b bo otth h h haan nd dss.. Never put your hands or feet in the cutting area. Do
not grasp the tool or place your hands too close to the blade. Keep your hands
well away from the blade. Never reach underneath the tool while the blade is in
motion. Do not use your legs or feet to stabilize the work piece.
P Po ossiittiio on n yyo ou urrsseellff tto o aavvo oiid d b beeiin ng g ccaau ug gh htt b beettw weeeen n tth hee tto oo oll o orr ssiid dee h haan nd dllee aan nd d
w waallllss o orr p po ossttss.. Should the blade become bound or jammed in the work, it could
result in loss of control and injury.
D Do o n no ott rru un n tth hee C Co orrd dlleessss R Reecciip prro occaattiin ng g S Saaw w w wh hiillee ccaarrrryyiin ng g iitt aatt yyo ou urr ssiid dee.. A mov-
ing blade could cause serious personal injury.
D Diisscco on nn neecctt b baatttteerryy p paacckk ffrro om m tto oo oll aan nd d p pllaaccee tth hee ssw wiittcch h iin n tth hee llo occkkeed d o orr
““O OFFFF”” p po ossiittiio on n b beeffo orree m maakkiin ng g aan nyy aasssseem mb bllyy,, aad djju ussttm meen nttss,, cch haan ng giin ng g aacccceess--
sso orriieess,, p peerrffo orrm miin ng g aan nyy iin nssp peeccttiio on n,, m maaiin ntteen naan nccee o orr cclleeaan niin ng g p prro occeed du urreess.. Such
preventive safety measures reduce the risk of starting the tool accidentally
which could cause serious personal injury.
D Do o n no ott u ussee tth hee C Co orrd dlleessss R Reecciip prro occaattiin ng g S Saaw w iiff iitt h haass b beeeen n d daam maag geed d,, lleefftt o ou utt--
d do oo orrss iin n tth hee rraaiin n,, ssn no ow w,, w weett o orr d daam mp p een nvviirro on nm meen nttss,, o orr iim mm meerrsseed d iin n lliiq qu uiid d..
D Do o n no ott u ussee d du ullll o orr d daam maag geed d b bllaad deess..
K Keeeep p ccu uttttiin ng g tto oo ollss ssh haarrp p aan nd d cclleeaan n.. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
W Wh heen n rreessttaarrttiin ng g aa ssaaw w iin n tth hee w wo orrkkp piieeccee,, cch heecckk tth haatt tteeeetth h aarree n no ott een ng gaag geed d iin n
tth hee m maatteerriiaall..
K Keeeep p tth hee h haan nd dllee o off tth hee C Co orrd dlleessss R Reecciip prro occaattiin ng g S Saaw w d drryy,, cclleeaan n,, aan nd d ffrreeee ffrro om m
o oiill aan nd d g grreeaassee..
B Bee eexxttrraa ccaarreeffu ull w wh heen n ccu uttttiin ng g iin n h hiig gh h o orr h haarrd d--tto o--rreeaacch h llo occaattiio on nss.. Be on the
lookout for hidden wires and falling debris.
M Maaiin nttaaiin n llaab beellss aan nd d n naam meep pllaatteess o on n tth hee C Co orrd dlleessss R Reecciip prro occaattiin ng g S Saaw w.. These
carry important information. If unreadable or missing, contact Alltrade for a
replacement.
7 8