APC WMR1000GI User Manual
Page 2
5.
In the Location or Address bar, enter http:// and
the current IP address for the wireless LAN, as set
on the AP/Router screen. The default value is
192.168.1.1.
For
example:
http://
192.168.1.1
6.
If the admin password was set on the System screen,
a prompt appears for the username and password.
Enter Admin for the username, and APC for the
password. The Mode Configuration screen
appears.
7.
Click the Configure button for AP/Router mode.
The AP/Router Mode Setup screen (Figure 8)
appears.
Figure 8. AP/Router Setup Screen
8.
Enter all relevant data. Refer to the APC 3-in-1
Wireless Mobile Router User’s Manual (on the
documentation CD) for more information.
Step 3c - Client Mode Setup
Figure 9. Client Mode Configuration
To configure the APC 3-in-1 Wireless Mobile Router for
Client mode, proceed as follows:
1.
Use the mode selector switch on the side of the
router to select Config mode (switch position 3).
2.
Power up the router and wait for the Ethernet LED
to come on, indicating that the router is ready.
Troubleshooting
Before contacting Technical Support, please refer to the
APC 3-in-1 Wireless Mobile Router User’s Manual on
the documentation CD, and to the technical information
available at: www.apc.com.
Warranty
The standard warranty is two (2) years from the date of
purchase. APC’s standard procedure is to replace the
original unit with a factory reconditioned unit. APC will
ship the replacement unit after the repair department
receives the defective unit, or cross-ship upon the receipt
of a valid credit card number. The customer pays for
shipping the unit to APC. APC pays ground freight
transportation costs to ship the replacement unit to the
customer.
Warranty Registration
To register this product for purposes of the warranty,
please go to warranty.apc.com.
APC Contact Information
990-214
5 Copyright © 2005 American Power Conversion
All rights reserved.
APC is a registered trademark of
American Power Conversion.
All other trademarks are
the property of their respective owners.
Technical Support
www.apc.com/support
Internet
www.apc.com
USA and Canada
866-WIFI-APC
France
0800 906 483
Asia-Pacific
(+65) 3896 823
China
(+86) (10) 8529 9888
Europe/Middle East/
Africa
(+353) 91 702020
Worldwide
(+1) 401 789 5735
3.
Establish a wired or wireless connection to the
router (Wired is recommended whenever possible).
For wired, connect a standard LAN cable from the
computer’s 10/100BaseT Ethernet port to the
Ethernet port on the Wireless Mobile Router.
For wireless, select the wireless network with the
SSID APC_AP.
4.
Start the Web browser.
5.
In the Location or Address bar, enter
config.ap
.
Note: This works only in Config mode.
6.
If the admin password was set on the System screen,
a prompt appears for the username and password.
Enter Admin for the username, and APC for the
password.
7.
The Mode Configuration screen appears. Click the
Configure button for Client mode. The Client
Mode Setup screen (Figure 10) appears.
Figure 10. Client Mode Setup Screen
8.
Enter all relevant data. Refer to the APC 3-in-1
Wireless Mobile Router User’s Manual (on the
documentation CD) for more information.
9.
Once setup is complete, use the mode selector
switch to select Client mode (switch position 4).
10. Restart your computer, or the device with which you
are using the APC 3-in-1 Wireless Mobile Router, in
Client mode.
6.
If the admin password was set on the
System
screen, a prompt appears for the
username
and
password
. Enter
Admin
for the username, and
APC
for the
password. The
Mode Configuration
screen appears.
7.
Click the
Configure
button for
AP mode
.
The
AP Setup
screen (Figure 6) appears.
Figure 6. AP Setup Screen
8.
Enter all relevant data. Refer to the
APC 3-
in-1 Wireless Mobile Router User’s Manual
(on the documentation CD) for more
information.
Step 3b - AP/Router Mode Setup
Note: By default, the APC 3-in-1 Wireless
Mobile Router allows both 802.11g and
802.11b connections.
Figure 7. AP/Router Mode Configuration
To configure the Wireless Mobile Router for
AP/Router mode
, proceed as follows:
1.
Use the mode selector switch on the side of
the router to select
Config
mode
(switch
position
3
).
2.
Power up the router and wait for the
Ethernet LED to come on, indicating that
the router is ready.
3.
Make sure that a connection is established
between the computer and the router (a
wired connection is recommended).
4.
Start the Web browser.