Audiovox Portable MP3 CD Player - Manual (Page 2)

DIGITAL SKIP PROTECTION SYSTEM
During playback, press EQ button to select different music mode.
Each time the EQ button is pressed, the music mode will be changed
to the next one as follows:
Normal (
) -> Bass ( ) -> Train ( ) -> Live ( ) ->
POP ( ) -> Jazz ( )
To play MP3-CDs
• This set can read CD, MP3 disc.
1. Place a MP3 disc with the label side up.
Push the disc gently until it clicks so that
the disc fits into the pivot.
2. Press the CD door to close.
3. Press “ ” to start playback.
The icon “ --- --- --- --- --- ” and the total number of
tracks will show on the display, and then
the current track number appears on the
display.
4. Press “ ” button to stop playback.
Searching a track
• You can search a track in playback mode or stop mode.
• In stop mode, the display will show the total number of tracks.
1. Press “
” or “ ” to search a track according to the desired
direction, each press skips one track. During play, the first press
on the skip backward “
” button goes to the beginning of the
current track.
2. In stop mode, press “ ” to start playback.
Searching a file by directory level
1. Press the DIR button to activate directory search mode. The word
“ DIR ” appears on the display.
2. Press “ ” or “ ” to search a file and then the first track number
in this file is displayed.
For example, total 50 tracks in MP3, 19 tracks (1-19) in the first file,
15 tracks (20-34) in the second file and 16 tracks (35-50) in the
third file. Press “
” button to the second file and “20 ” (the first
track number in second file) appears on the display; Press “ ”
button to the third file and “35 ” appears on the display.
4. Press DIR button again, the word “ DIR ” disappears. It goes back
to the default mode.
5. Press “ ” or “ ” to search a desired track.
With a conventional portable CD player, you might have experienced
that the music stopped. e.g. When jogging the ELECTRONIC SKIP
PROTECTION protects against loss of sound caused by vibrations
and shocks.
• When start to play CD disc, press ESP ON/OFF button to activate
the ELECTRONIC SKIP PROTECTION function, the“ ” icon
appears in the display window and the protection is activated.
• To cancel the ELECTRONIC SKIP PROTECTION function when play
CD disc, press ESP ON/OFF button to turn off and the “ ” icon
disappears in the display window.
• The ELECTRONIC SKIP PROTECTION is default when play MP3
disc, cannot deactivate it by pressing the ESP ON/OFF button.
Note:
• When the DIGITAL SKIP PROTECTION SYSTEM is switched on or
off, the sound will be interrupted for a short time. This is normal.
Should any problem persists after you have made the following
checks, consult your nearest service facility.
Disc play does not start:
• The disc is inserted upside down or incorrectly. Insert the disc
correctly with the label surface up.
• Dusty or defective disc.
• Dirty or dusty lens.
• The disc compartment lid is not closed.
• Moisture condensation -> Leave the unit in a warm place until the
moisture evaporates.
• The AC power adaptor is not plugged into the wall outlet.
• The unit is not placed on a level surface.
• Weak batteries.
No sound from the headsets:
• The headphones / earphones plug is not firmly connected to the
“ PHONES ” jack .
• Adjust the “ VOL ” control.
• Dirty plug.
Skipping of sound:
• Dirty or defective disc.
• Dirty lens.
• Strong vibration.
When using with batteries the battery life is short:
• Use alkaline batteries and not manganese batteries.
The unit can not be operated:
• No disc , dirty disc or scratched disc. The unit will return to full
stop mode after approx. 30 seconds, or reset the player by pressing
“ ” and then insert a disc to start playing.
• When recording on CD-R discs, use 74-minute (650M) discs. Do
NOT use 80-minute (700M) discs.
• The CD-R or CD-RW discs should be “finalized” in computer by
“single section format”.
Printed in China
811-873391-021
Cleaning the unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with
a soft cloth.
Cleaning CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from the centre out with a clean cloth.
After playing, store the disc in its case.
Handling the disc
Only touch the CD on the edge to avoid finger prints on its surface.
Do not stick paper or tape, or write anything on the surface.
Power requirements 2 “ AA ” size (LR6 or UM-3) alkaline
batteries, or DC IN 6V,
350mA power adaptor
Polarity of plug
Operating voltage AC100V 50/60Hz (Japan)
AC120V 60Hz (U.S.A, Canada)
AC220-240V 50Hz
(Singapore, Malaysia & Thailand)
AC230V 50Hz (Chile)
AC230V-240V 50Hz (Europe)
AC240V 50Hz (Middle East & Australia)
We continually strive to improve our products, specifications
may change without prior notice.
During pause
The current track will flash.
When no disc is inserted into the player and if “ ” is pressed, the
display window shows "
".
The unit can not be operated when the message is displayed. After
approx. 30 seconds the unit will return to full stop mode, or reset the
player by pressing “ ” button and then insert a disc to start playing.
VARIOUS PLAYING MODES
During playback, each time the PLAY MODE button is pressed, the
mode will be changed to the next one as follows:
NORMAL Play -> ( ONE ) Repeat One -> ( ALL ) Repeat All
-> (INTRO) Intro Scan -> SHUFF -> ( SHUFF ) SHUFF All
NORMAL Play - Playing the whole disc
The CD is played once from beginning to end.
Repeat Play (Repeat One / Repeat All)
• To repeat the same track
Press PLAY MODE during play until
Repeat One “
ONE ” appears in the
display window. Select the desired track
to be played by pressing “
” or “ ”.
• To repeat the whole disc
Press PLAY MODE during play until
“
ALL ” appears in the display
window.
INTRO Play - Playing the First Ten seconds of each track
1. Press PLAY MODE button during play
until INTRO appears in the display
window.
2. It starts INTRO play automatically (play
each track for approx 10 second).
• Automatically INTRO play always starts
from the track that immediately follows
the current running one.
• By pressing “ ” , “ ”, you may
start intro play from the selected track.
SHUFF Play - Playing the selections in random order
1. To shuff
Press PLAY MODE button during play
until SHUFF appears in the display
window. After all tracks are played, the
system will stop automatically.
• To locate the next track:press “
”.
However, you can not locate a
previous track even if you keep “
”
pressed.
2. To shuff all
Press PLAY MODE during play until
“SHUFF
” appears in the display
window. All tracks will play without
sequence repeatedly.
• To locate the next track:press “
”.
However, you can not locate a
previous track even if you keep “
”
pressed.
Notes:
• In any play mode, it starts running automatically after a few seconds
without pressing “ ” button.
• “ ” button works during any play mode to hold or resume the
current play mode.
• To cancel current play mode
1. Press PLAY MODE button during play to change play mode.
2. Press PLAY MODE button during play until it goes back to normal
play.
Program Play - Playing the selections in the desired order (In
stop mode only)
1. In stop mode, press the PROGRAM
button, “000” will appear in the display
window and flash.
2. Press “ ” or “ ” button to select the
desired track.
3. Press the PROGRAM button to store this
track in memory.
4. Repeat steps 2 and 3 to register other
tracks.
5. Press the “ ” button to start play and
“ PROG ” shows in the display window.
6. To stop program play, press the “ ”
button.
Pause mode of the second track
DIGITAL SKIP PROTECTION SYSTEM
EQ FUNCTION
MP3 - CD PLAYBACK
TROUBLE SHOOTING GUIDE
MAINTENANCE
SPECIFICATIONS
To Edit Program Play:
To check:
Press PROGRAM button lightly during programming
before you press “ ”. Each time the PROGRAM button
is pressed until the program number appears in the
display window.
To add: To add additional tracks to your selection in stop mode,
press “ ” button first and then press PROGRAM button
repeatedly until “000” appears in the display window.
Repeat the above steps 2 and 3 to store additional tracks.
To change: When checking, press either “ ” or “ ” button to alter
the track number for the program currently displayed.
Press PROGRAM button to register the newly selected
track into memory.
To delete: Open the CD door or press “ ” button twice.
Notes:
• Repeat play can be performed during program play.
• The program is also erased when the disc compartment is opened
or the auto power off function turns the power off.
• To cancel program operation, press “ ” button once.