Sony HT-DDW670 User Manual
Page 41
Ad
dition
al I
n
fo
rm
atio
n
masterpage:Right
lename[E:\SEM_Janet\Revision
Data\J9050000_2342216141DDW670_GB\2342216141\GB09ADD_HT-DDW670-U.fm]
41
GB
model name1[HT-DDW670]
[2-342-216-14(1)]
Models of area code AU
(6 ohms 120 Hz – 20 kHz, THD 0.09%)
FRONT
2)
: 40
W/ch
CENTER
2)
: 40
W
SURR
2)
: 40
W/ch
(6 ohms 100 Hz, THD 0.09%)
SUB WOOFER
2)
: 40
W
(6 ohms 1 kHz, THD 0.7%)
FRONT
2)
: 50
W/ch
CENTER
2)
: 50
W
SURR
2)
: 50
W/ch
(6 ohms 100 Hz, THD 0.7%)
SUB WOOFER
2)
: 50
W
(6 ohms 1 kHz, THD 10%)
FRONT
2)
: 85
W/ch
CENTER
2)
: 85
W
SURR
2)
: 85
W/ch
(6 ohms 100 Hz, THD 10%)
SUB WOOFER
2)
: 85
W
1) Measured under the following conditions:
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
Inputs (Digital)
Output (Analog)
Reproduction frequency range:
28 – 20,000 Hz
Tone
FM tuner section
Tuning range
87.5 - 108.0 MHz
Antenna
FM wire antenna
Antenna terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1,710 kHz
3)
With 9-kHz tuning scale: 531 – 1,710 kHz
3)
Models of area code CEL, CEK, AU, SP
With 9-kHz tuning scale: 531 – 1,602 kHz
Model of area code E51
With 10-kHz tuning scale: 530 – 1,610 kHz
3)
With 9-kHz tuning scale: 531 – 1,602 kHz
3)
Models of area code MX
With 10-kHz tuning scale: 530 – 1,610 kHz
Antenna
Loop antenna
Intermediate frequency
450 kHz
3) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
General
Power requirements
Power consumption
Area code
Power requirements
U, CA
120 V AC, 60 Hz
CEL, CEK, SP
230 V AC, 50 Hz
AU, E51
240 V AC, 50 Hz
MX
127 V AC, 60 Hz
SA-CD/CD, DVD,
VIDEO 1, 2
Sensitivity: 800 mV
Impedance: 50 k ohms
DVD (Coaxial)
Sensitivity: –
Impedance: 75 ohms
SA-CD/CD (Optical)
Sensitivity: –
Impedance: –
SUB WOOFER
Voltage: 2 V
Impedance: 1 k ohm
Gain levels
±6 dB, 1 dB step
Area code
Power requirements
U, CA
120 V AC, 60 Hz
CEL, CEK
230 V AC, 50/60 Hz
AU
240 V AC, 50 Hz
E51
120/220/240 V AC,
50/60 Hz
SP
220-230 V AC, 50/60 Hz
MX
127 V AC, 60 Hz
Area code
Power consumption
U, SP, E51, AU, CEL,
CEK, MX
160 W
CA
220 VA
continued
GB01COV_HT-DDW670-U.book Page 41 Wednesday, July 13, 2005 1:45 PM