Sony PS-LX350H - Manual (Page 9)

9
Additional Information
Platter does not rotate.
b Make sure the power cord is inserted all the way into
an AC wall outlet.
b The drive belt is not completely hooked onto the
motor pulley. Make sure the belt is hooked
completely around the motor pulley (see page 4).
The drive belt is broken.
b Replace the drive belt. For details, please make a
contact with Sony dealer.
Sound is too low or distorted.
b The turntable is not connected to the PHONO inputs
on the amplifier (see page 4).
* This phenomenon, called “acoustic feedback”, occurs
when vibrations from the speakers are transmitted
through the air or via solid objects (such as shelves, a
cabinet, or the floor) to the turntable where they are
picked up by the stylus, amplified and reproduced
through the speakers.
Specifications
Motor and Platter
Drive system
Belt-drive
Motor DC motor
Platter 330 mm dia. Aluminum die-cast
Speeds 33 1 /
3
and 45 r/min, 2 speed
Wow and flutter Less than 0.25% (WRMS)
Signal to noise ratio More than 50 dB (DIN-B)
Tone Arm
Type
Static balanced S-shaped tone arm with
detachable headshell
Effective arm length 220 mm
Overhang 10 mm
Usable cartridge weight 6 g (min.) to 10 g (max.)
General
Power requirements
U.S.A.: 120 V AC, 60 Hz
European countries: 220 ~ 230 V AC,
50/60 Hz
Other countries: 110 ~ 120 V/220 ~
240 V AC, 50/60 Hz
Power consumption 8 W
Dimensions Approx. 450 x 145 x 350 mm (17 11 /
16
x
5 11 /
16
x 13 3 /
4
in) (w/h/d)
Mass 6.5 kg (14 lb 5 oz)
Supplied Accessories
45 r/min adaptor (1)
Platter (with drive belt) (1)
Rubber mat (1)
Cartridge and headshell (1)
Counter weight (1)
Audio connecting cord (1)
Dust cover (1)
Design and specifications are subject to change without notice.
Troubleshooting
Before going through the check list below, first make
sure that:
• The power cord is securely connected.
• The speaker cords are securely connected.
Should any problem persist after you have made these
checks, consult your nearest Sony dealer.
The tone arm skips, skates or does not advance.
b The turntable is not level. Place the turntable on a
level surface.
b Incorrect tracking force. Follow the instructions on
page 5 and set the tracking force to the appropriate
value for the cartridge being used. (The supplied
cartridge requires 2 grams of tracking force.)
b Incorrect anti-skating adjustment. Make sure the
ANTI-SKATING dial is set to the same value shown
on the tracking force ring (see page 5).
b The record is dirty or scratched.
Clean the record with a commercially available
record cleaning kit, or replace the record.
Poor sound quality, excessive noise, intermittent sound,
etc…
b Check the tone arm locking collar to make sure the
headshell is securely attached to the tone arm (see
page 4).
b Make sure the earth lead is connected to the earth
terminal on the amplifier (see page 4).
b Incorrect tracking force. Follow the instructions on
page 5 and set the tracking force to the appropriate
value for the cartridge being used. (The supplied
cartridge requires 2 grams of tracking force.)
b The stylus is dirty or worn. Remove dust on the
stylus using a stylus cleaning brush, or replace the
worn stylus (see page 7).
b Dust or dirt has collected on the record. Clean the
record using a good quality record cleaner.
b Check that the cartridge lead wires inside the
headshell are firmly attached.
Rumble or low-frequency howl*.
b The turntable is placed too close to speakers. Move
speakers away from the turntable.
Tempo is incorrect.
b Incorrect r/min. Set the r/min setting to match the
one indicated on the record. (Select “33” for 33 1 /
3
r/
min records or “45” for 45 r/min records.)
b The PITCH CONTROL is not set to the center
position.
b Incorrect platter speed. Adjust the fine controls on the
bottom of the turntable while watching the strobo
dots to obtain correct platter speed (see page 6).
The drive belt is deteriorated.
b Replace the drive belt. For details, please make a
contact with Sony dealer.