Sony MDS-JE440 - Manual (Page 37)

37
masterpage:Right filename[\\Win-35\logitecmo\422958711MDSJE640CED\01GB03OPE-CED.fm]
Naming a track or MD/Changing the recorded level after recording
Editin
g Rec
o
rd
ed
MDs
model name1[MDS-JE640] model name2[MDS-JE440]
[4-229-587-11(1)]
3 Do steps 5 to 8 of “Naming a track or an MD using
the controls on the deck” on page 35 or steps 2 to 4
of “Naming a track or an MD using the remote” on
page 36.
4 Press YES.
The whole name appears in the display, followed by
“Complete!!” to indicate that the labeling procedure is
completed.
Use this function to erase the name of a track or disc.
1 While the deck is stopped, playing, recording, or
paused, press MENU/NO.
“Edit Menu” appears in the display.
2 Turn AMS (or press . / > repeatedly) until
“Name ?” appears, then press AMS or YES.
3 Turn AMS (or press . / > repeatedly) until “Nm
Erase ?” appears, then press AMS or YES.
4 Turn AMS (or press . / > repeatedly) until the
number of the track (when erasing the track name)
or “Disc” (when erasing the disc name) flashes,
then press AMS or YES.
“Complete!!” appears for a few seconds and the name
is erased.
To cancel the operation
Press MENU/NO or x.
You can erase all the track names and the disc name on an
MD in a single operation.
1 While the deck is stopped, playing, or paused,
press MENU/NO.
“Edit Menu” appears in the display.
2 Turn AMS (or press . / > repeatedly) until
“Name ?” appears, then press AMS or YES.
3 Turn AMS (or press . / > repeatedly) until “Nm
All Ers?” appears, then press AMS or YES.
“Nm All Ers??” appears in the display.
4 Press AMS or YES.
“Complete!!” appears for a few seconds and all the
names on the MD are erased.
To cancel the operation
Press MENU/NO or
x.
z
You can erase all the recorded tracks and names on
the MD
For details, see “Erasing all the tracks on an MD” on page 32.
Changing the recorded
level after recording
(S.F EDIT)
You can change the volume of recorded tracks using S.F
(Scale Factor) Edit. The original track is recorded over at
the new recording level. When changing the recording
level, you can select Fade-in Recording to gradually
increase the signal level at the start of recording, or Fade-
out Recording to gradually decrease the signal level at the
end of recording.
1 For MDS-JE640, press S.F EDIT.
“S.F Edit” appears in the display.
For MDS-JE440, do the following:
1 Press MENU/NO.
“Edit Menu” appears in the display.
2 Turn AMS (or press . / > repeatedly) until “S.F
Edit?” appears, then press AMS or YES.
2 Turn AMS (or press . / > repeatedly) until “Tr
Level ?” appears, then press AMS or YES.
3 Turn AMS (or press . / > repeatedly) until the
track number you want to change the recording
level appears, then press AMS or YES.
“Level 0dB” appears in the display.
4 MDS-JE640
While monitoring the sound, turn AMS (or press
. / > repeatedly) to change the recorded level
without turning on the two rightmost indicators on
the peak level meters.
You can set the level at any value between –12 dB and
+12 dB, in 2 dB increments.
Erasing a track or disc name
Erasing all the names on the MD
Changing the overall recording level
AMS
YES
AMS S.F EDIT
Avoid turning on these indicators